Patriot Guard Windshield Banner attachment

[Buckeye Bleau]

I have been trying to figure out the best way to place the 6 x 24 (guessing on the dimensions) PGR banner across the windshield on my RT.

I finally decided to make inquiry to the experts here, I know that there are other PGR members here, and perhaps I could profit from your experience.

Thank you in advance,
Joe :chat:

 

[derrill]

My wife and I haven't figured it out either. We put a flagpole on the trailer hitch.


Sent from my iPad using Tapatalk

 

[bmwlarry]

I rode with the PG for about a year until my back couldn't do the standing. I placed the banner across the outside of the windshield with the bottom edges tucked under the chrome window trim. there is just enough room. Then on the side edges I used those clamp type office document holders (two each side). finally i used two very tiny bungie cords stretched across behind the windshield connecting the holes in the banner. I hope this helps.

 

[cyclekid58]

Patriot Guard Banner

I rode with the PG for about a year until my back couldn't do the standing. I placed the banner across the outside of the windshield with the bottom edges tucked under the chrome window trim. there is just enough room. Then on the side edges I used those clamp type office document holders (two each side). finally i used two very tiny bungie cords stretched across behind the windshield connecting the holes in the banner. I hope this helps.

I do the same exact thing, those clips he mentioned are binder clips, I got mine in silver and they don't show as much. If you try and go over the windshield brackets it creeps up and pops loose, I also lower the windshield a little so no vision obstruction. I also have the Rivco flag holders that bolt to the trunk and hold the 6"x9" flags.

 

[flaggerphil]

I used binder clips while I was still riding with them.

 

[Bfromla]

I have seen many bikes spyder or not using the above mentioned binder clips:firstplace: allows for EZ adjustment pre & post escort, most do not use at highway speeds fyi, some also use small bungee cords & the clips (double secure) I chose the decal as I look right over my windshield anyway

. Works for me. SmoothSpyder backrest holds my 8x12flag just great:thumbup:. Talk with your ride captin see if they may hay a temp one you can test out, or point you to another member can show you directly.

 

[bmwlarry]

I also run a Rivco with a full size flag

 

[thunor]

PGR banner

I just use the small bungies. I did go through shopping a number of them to get one small enough to
provide enough tension to not "lose it". Mine stays in place easily at Highway speeds(70-80).

 

[Dragonfly]

Decided to put it across the top of the frunk with and placed a 6" strip of Velcro underneath on booth sides and on the banner, had it up to 73 mph without any problems. Never could find a good way to put on the windshield especially with my camera mounted behind the windshield.

 

[FALCOR]

I have been trying to figure out the best way to place the 6 x 24 (guessing on the dimensions) PGR banner across the windshield on my RT.

I finally decided to make inquiry to the experts here, I know that there are other PGR members here, and perhaps I could profit from your experience.

Thank you in advance,
Joe :chat:

I to am a PGR Vietnam Era Vet.
DO YOU KNOW HOW TO MOUNT FLAGS ON 2015 RT?

THANK YOU,
FALCOR

 

[FALCOR]

Flag mount

I do the same exact thing, those clips he mentioned are binder clips, I got mine in silver and they don't show as much. If you try and go over the windshield brackets it creeps up and pops loose, I also lower the windshield a little so no vision obstruction. I also have the Rivco flag holders that bolt to the trunk and hold the 6"x9" flags.

I Have a 2015 RT. I'm looking for flag mounts for my trunk. I do not have bolt holes.
any idea?

Thanks,
FALCOR

[email protected]