-
There were many reasons for the change of the site software, the biggest was security. The age of the old software also meant no server updates for certain programs. There are many benefits to the new software, one of the biggest is the mobile functionality. Ill fix up some stuff in the coming days, we'll also try to get some of the old addons back or the data imported back into the site like the garage. To create a thread or to reply with a post is basically the same as it was in the prior software. The default style of the site is light colored, but i temporarily added a darker colored style, to change you can find a link at the bottom of the site.
OIL USEAGE
- Thread starter ma and pa
- Start date
My 08 used less than a half quart, every 3 thousand miles.
Anywhere from a half to a quart would probably be considered normal.
Now if your over filling you'll be burning off the extra pretty quick.!
Farmboy
New member
I feel that BRP should never use.."start out with semi synthetic" at all. A good old stand by oil out of the ground till at least first 1000 miles so the rings get there grove cut and sealing. Then go full synthetic. Never had a "new bike of any kind" to use oil. But because they started with synthetic, they will NEVER stop using oil unless we re ring them and start all over again. "my 2 cents worth"
NancysToy
Motorbike Professor
NicaSil cylinders and moly rings do not need (or benefit from) the break-in procedures that old engine technologies required. The rings are seated during the first few revolutions. You cannot wear into the hard cylinder walls, and there is no cross-hatch pattern to wear into. The oil usage here is not really due to burning oil, but to other issues like venting to the airbox. If any oil is pulled past the rings or valve guides, it would be because synthetics cling so well and are so slippery. Unfortunately, dino oils do not provide adequate lubrication, resistance to shearing, superior film strength, and other characteristics that these modern engines need. If the manufacturer, like BMW, says to use a break-in oil (usually dino oil), by all means do so. Those BMW models have conventional cast iron cylinder liners, and require the break-in. If a semi-synthetic is specified, or even a full synthetic, I'd go that route, especially with hardened cylinders. They don't just have an intern dream this stuff up. Their recommendations are based on the materials and methods used, factory tests, and sound engineering. JMHO
Yes, the break-in was dino oil and no specification of either type later. But for those that switched to synthetics right away for the extra protection, they were burning more that those who continued using dino until it stopped burning or reduce to a smaller amount. And I believe they are Nikasil cylinders.
I do appreciate your opinion. Cheers.
I do appreciate your opinion. Cheers.
BajaRon
Well-known member
I started using Amsoil at the 600 mile oil change (which I did myself). My oil consumption has not varied all that much over time. I've now got 31,000 miles on my Spyder. I don't think having to add less than 1/2 quart during our latest 6,000 mile trip in June is all that bad.
It is impossible to argue with someone elses experience but the facts back Scotty on this one.
High RPM, high compression, high performance engines will always use more oil than their slow revolution, lower compression counterparts.
But I think everyone has come to the same, correct conclusion on one point. If you want increased engine wear, don't use full synthetic oil.
It is impossible to argue with someone elses experience but the facts back Scotty on this one.
High RPM, high compression, high performance engines will always use more oil than their slow revolution, lower compression counterparts.
But I think everyone has come to the same, correct conclusion on one point. If you want increased engine wear, don't use full synthetic oil.
Farmboy
New member
Very true, I agree. but why do our spyders... Use oil... no others do? I really don't have any other answer. I don't think any one does...I have not found any oil in air box as of yet. at 5000 miles about a full quart so far. my yamaha 28000 and not a drop below full at oil change time and Never had to add a drop. one 4 wheeler and 1 car, 1 truck one riding lawnmower one 40 hp tractor one river boat "4 stroke". all I got new and never had to add oil. or had to worry to take a bottle with me. dont get me wrong I am not talking bad about my spyder... just trying to make a point. we read about "limp nodes" "heat" etc... Its obvious that BRP engineering do not own a spyder:roflblack: sorry. just my "1 cent" on this one. Sure glad I love my spyder to put up with it.:bowdown:
BajaRon
Well-known member
I agree that the Spyder uses too much oil compared to just about anything else. I'd be curious as to what oil usage is on the Aprilia.
My comparrison was apples to apples with other Spyders.
Ga Blue Knight
New member
Past experiences with the Rotax engine, many different cc's and applications would indicate that they all used oil at some level of consumption. It's just the nature of the engine design.
My 08 didn't use enough oil between changers to worry about, None of my previous bikes [Japanese] used oil ether. As a matter of fact my Tri Glide in over 10 thousand mile's hasn't used Any.
I think oil usage with the Spyder or most modern engines now days is not a problem,
In my opinion its a lot to do about nothing. :dontknow:
I think oil usage with the Spyder or most modern engines now days is not a problem,
In my opinion its a lot to do about nothing. :dontknow:
Similar threads
