Converting 6 pole WAGS trailer to 4 pole square Spyder

[Blue3]

Any guidance anyone can give will be greatly appreciated

 

[billybovine]

Any guidance anyone can give will be greatly appreciated

Get a wiring diagram from the trailer manufacturer would be a good first step.

 

[Blue3]

Used trailer

What does each wire on the Spyder 4 square connector handle?

Sorry about duplicated posts. I hope extras deleted.

 

[billybovine]

White wire is ground.
Brown is taillights.
Yellow is left turn and brake.
Green is right turn and brake.

 

[Blue3]

trailer wiring

Picking up trailer far from home. It has the amber turn signal lights. Could I take those wires to the respective 4-square and use them as both turn and brake lights and the red as only tail lights? I could change the lens to red which seems easier than re-wiring the trailer to separate the existing brake lights into turn/brake.

Thanks for all the help.

 

[Bfromla]

Picking up trailer far from home. It has the amber turn signal lights. Could I take those wires to the respective 4-square and use them as both turn and brake lights and the red as only tail lights? I could change the lens to red which seems easier than re-wiring the trailer to separate the existing brake lights into turn/brake.

Thanks for all the help.

If you are in a time crunch maybe & only if you had informed escort to help:lecturef_smilie:
Just you & general traffic:yikes: No way,not me bud, Id find another way to transport it!
Inside a truck bed or another trailer with good lighting Get it home & get the lights right better than rear-ended from crazy light issues.

 

[ChicoFowler]

Any guidance anyone can give will be greatly appreciated

Check out Hopkins 47975 - 4 pin square. I had to connect a 4 pin round to my bike. Bought a standard 4 pin round and this Hopkins connect and made up a short connect between the Spyder and the trailer.

 

[billybovine]

Picking up trailer far from home. It has the amber turn signal lights. Could I take those wires to the respective 4-square and use them as both turn and brake lights and the red as only tail lights? I could change the lens to red which seems easier than re-wiring the trailer to separate the existing brake lights into turn/brake.

Thanks for all the help.

The trailer has amber turn signals. That means it is not a 4 wire system like the Spyder. But we still don't know if the trailer is actually a 6 wire or 5 wire system. Highly likely it's 5 wire. Then you need an electronic converter and build an adapter using that. Here is an example of one I found when I did a google search. https://www.etrailer.com/Accessories-and-Parts/Curt/C56196.html It separates the combined right and left brake/turn into right turn, left turn and brake.

 

[Blue3]

Used trailer

The trailer has amber turn signals. That means it is not a 4 wire system like the Spyder. But we still don't know if the trailer is actually a 6 wire or 5 wire system. Highly likely it's 5 wire. Then you need an electronic converter and build an adapter using that. Here is an example of one I found when I did a google search. https://www.etrailer.com/Accessories-and-Parts/Curt/C56196.html It separates the combined right and left brake/turn into right turn, left turn and brake.

..
Thank you. This appears to be the solution. One of the reviews was for a Spyder. Some reviews mentioned a diode, is this necessary? Thank you again.

 

[billybovine]

..
Thank you. This appears to be the solution. One of the reviews was for a Spyder. Some reviews mentioned a diode, is this necessary? Thank you again.

There should be no need for any diodes on a trailer. Diodes would only be needed if your where towing a car.

 

[Blue3]

There should be no need for any diodes on a trailer. Diodes would only be needed if your where towing a car.

Thank you so much. I got the Curt magic box and all works well. I am sure I would have been in deep do do without your help.