• There were many reasons for the change of the site software, the biggest was security. The age of the old software also meant no server updates for certain programs. There are many benefits to the new software, one of the biggest is the mobile functionality. Ill fix up some stuff in the coming days, we'll also try to get some of the old addons back or the data imported back into the site like the garage. To create a thread or to reply with a post is basically the same as it was in the prior software. The default style of the site is light colored, but i temporarily added a darker colored style, to change you can find a link at the bottom of the site.

Lost a body panel. :-(

markyodo

New member
It was a breezy day on Saturday. I guess that is an understatement!
Cruising the highway enjoying a beautiful 46 mile ride to a friends house and when I got there I noticed the right side body panel was gone.
The entire ride was head on into the constant wind and there were a couple wind gusts which noticeably pushed the bike. I am guessing one of those gust went straight past the wheel well and into the engine compartment pushing it up and out like a kite. There was no luck finding it on the road side the next day.
It's an expensive $200 ride.

The pic is of the left side equivalent to the missing one.
attachment.php


Has anyone else had this happen, or know of a better solution to securing the plastic/rubber push pins?
Thanks...
 

Attachments

  • panel.jpg
    panel.jpg
    25.7 KB · Views: 25
  • panel.jpg
    panel.jpg
    15.9 KB · Views: 428
Last edited:
One suggestion that i can make is when you (or others) take that or any panel off for any reason, before you put it back on .................... Spray a shot of windex into each one of the rubber grommets on the Spyder, when you do it helps the peg to go into the grommet easier and the windex dries very quickly and has a minor amount of stickiness to it that helps hold the panel on, also be sure that all of the pegs are in the grommet securely. Never use any type of oily or greasy (wd-40 etc) lubricant or cleaner on the rubber grommets.

Cruzr Joe
 
The grommets probably had been pushed through and that is why it came off. Be sure to check the panels, especially after you have it in for service, to be sure they are on securely. If you put them on in a hurry and aren't careful you can easily push the grommets through. And as Cruzr Joe said use Windex - don't use grease. The idea is to get them on easily and have them stay on.
 
THIS PART

It was a breezy day on Saturday. I guess that is an understatement!
Cruising the highway enjoying a beautiful 46 mile ride to a friends house and when I got there I noticed the right side body panel was gone.
The entire ride was head on into the constant wind and there were a couple wind gusts which noticeably pushed the bike. I am guessing one of those gust went straight past the wheel well and into the engine compartment pushing it up and out like a kite. There was no luck finding it on the road side the next day.
It's an expensive $200 ride.

The pic is of the left side equivalent to the missing one.
attachment.php


Has anyone else had this happen, or know of a better solution to securing the plastic/rubber push pins?
Thanks...
....Check here for a better price....PROCALIBER.COM -- if you register ( it's free ) the prices shown will be the dis-counted prices......and they ship for free $99.00 and over ( total order )....Mike
 
I put a small ziptie around the grommet. Keep it in place and keep from losing it. I was using Vaseline on the grommets but not anymore. I like the Windex idea better.
 
I always install lanyards on my GoldWings' pop-out panels, and I will be doing the same on my wife's Spyder very soon.
 
If you pull off the opposite side panel on the inside you will see a small plastic clip that is part of the panel in the vicinity of where you show part #365 in your illustration. If that clip is not snapped down firmly onto the panel above it, I believe it's PN705007105, it seems possible a strong wind could lift the lateral side panel away from the Spyder leaving nothing but the pins and rubber grommets holding it in place. Just a semi-educated guess.
 
I lost one soon after buying my Spyder, and made the dealer replace it under warranty. I came home and used a piece of plastic coated wire and two tie wraps to secure both panels to the bike. There is also a post on the forum where a member used a small carabiner so you can unclip the panel if needed.
 
If you pull off the opposite side panel on the inside you will see a small plastic clip that is part of the panel in the vicinity of where you show part #365 in your illustration. If that clip is not snapped down firmly onto the panel above it, I believe it's PN705007105, it seems possible a strong wind could lift the lateral side panel away from the Spyder leaving nothing but the pins and rubber grommets holding it in place. Just a semi-educated guess.

This is correct, and snapping the clip under the panel above is what puts the panel under tension and holds it there.
 
I have my panels wired to the frame. I wound one end of the wire under the screw that holds the chrome Can-Am piece #187 on to the panel, the other end on a caribiner through a hole in the frame. Left one came off once, but the wire saved it. Cheap & easy. Sorry you have to buy a new panel.

Edit: That's me post # 9. I will try and find the pictures I took and post them.
 
Last edited:
Great advice from everyone as always.
Calling the dealership today to get my warranty details.
The grommets are all still in place, but I did notice they had a bit of grease or something on them. I assume the manufacturer or dealer does this.
Windex, zip ties, lanyards, wires are all great ideas. oldguyinCT, if you have pics that would be awesome! ;)
 
Great advice from everyone as always.
Calling the dealership today to get my warranty details.
The grommets are all still in place, but I did notice they had a bit of grease or something on them. I assume the manufacturer or dealer does this.
Windex, zip ties, lanyards, wires are all great ideas. oldguyinCT, if you have pics that would be awesome! ;)

Here is a picture.

attachment.php
 

Attachments

  • 20160224_102559.jpg
    20160224_102559.jpg
    49.1 KB · Views: 213
I spoke with the dealer (maintenance) yesterday, who called me back today and informed me that BRP would not replace the piece(s) under warranty. Bummer..
 
A good idea to check body panels before rides.

Every time I bring my :spyder2: in for an oil change service, the mechanic fails to properly latch the panels. When mentioned to the service advisor, I get a "this is not my first rodeo" reply. In other words, they don't want any advice or information from the peanut gallery.

I always re-set the panels properly before I drive off from the service. Also, I always check out that panels are inserted before any rides. Saves a lot of grief.

And...I am biding my time with the wise guy service advisor. The owner is aware, but its the only service department I can go to for now. I still like my :ani29::spyder2: so am stuck for the moment.
 
It was a breezy day on Saturday. I guess that is an understatement!
Cruising the highway enjoying a beautiful 46 mile ride to a friends house and when I got there I noticed the right side body panel was gone.
The entire ride was head on into the constant wind and there were a couple wind gusts which noticeably pushed the bike. I am guessing one of those gust went straight past the wheel well and into the engine compartment pushing it up and out like a kite. There was no luck finding it on the road side the next day.
It's an expensive $200 ride.

The pic is of the left side equivalent to the missing one.
attachment.php


Has anyone else had this happen, or know of a better solution to securing the plastic/rubber push pins?
Thanks...
Shortly after purchasing I added retainers. I wired key ring clips so they are easily removable. The wires are short enough that if the panel comes free it won'd get caught up in anything. The photos show zip ties which I used to test my idea. I replaced them with picture hanger wire. Thin and flexible but sturdy.

CJ JAX
 

Attachments

  • 20140609_203652.jpg
    20140609_203652.jpg
    29.4 KB · Views: 31
  • 20140609_203640.jpg
    20140609_203640.jpg
    29.5 KB · Views: 27
Back
Top