To kill or not to kill (switch), that is the question

[Pirate]

How many use the kill switch to shut the bike down?

I never use it.

 

[Valkrocket]

Always. Since I was 16 years old.... and that was a LONG time ago. And Yes I have had that WTF moment on the interstate when I accidently bumped it, but that only will happen once. You learn fast when your heart goes up to your throat in panic mode. Think about it guys, if it wasn't necessary, BRP would have removed it from their lines long ago and saved some $$ in production costs. Name a motorcycle that doesn't have a kill switch. I dare ya. :dontknow:

 

[Peter Aawen]

Always. Since I was 16 years old.... and that was a LONG time ago. And Yes I have had that WTF moment on the interstate when I accidently bumped it, but that only will happen once. You learn fast when your heart goes up to your throat in panic mode. Think about it guys, if it wasn't necessary, BRP would have removed it from their lines long ago and saved some $$ in production costs. Name a motorcycle that doesn't have a kill switch. I dare ya. :dontknow:

Errr, that's only cos they are STILL mandated by International Agreements & national legislation iaw those agreements. ..... despite the circumstances & fittings that caused them to be required in the first place having been removed from ALL motorcycles quite some years ago! :banghead:

BRP only includes them because they're legally required to - I'd suggest that the moment they can work out a way around that requirement &/or it's dropped, then BRP won't install them any more. :thumbup:

Just Sayin' :cheers:

 

[jerrydonna]

At the insistence and support of the battery makers, motorcycle mfrs install kill switches to sell more batteries to those who use the kill switch and walk away w/o turning off the igniton. Best policy; Turn of the ignition and immediately remove the key.

have done that a couple times, now I just key it. and also my Moto Guzzi key is in the right place

 

[jerrydonna]

on a long ride just a couple days ago (12 hours) my wife who was behind me called out over MIC .... "I think I have a problem", .....waiting for next reply I looked back and saw her slowing down. SO WHATs the Trouble I say.
her next reply was "I have no Power" I say ok just pull the bike off as far as possible off the road. MY mind is GOING fast and running thru all the issues like GAS OUT...NO,
before I could turn my bike around I think OK she Killed IT. As I make another u turn behind her I ask her if she pushed that RED Ejector Botton. Hell yes... she wasn't happy doing something so stupid. She hasn't used that KILL switch for the past couple years after class. I said what until you press the Button getting off or on and when you think of it fast enough you JUST THINK ...**** how is the battery dead,, and hope you figure it out before calling for help...

 

[vito1943]

The best use of the "kill switch" is to flip it on a buddies bike when you stop to eat, gas up, etc. Then watch him go a bit crazy when the bike won't re-start. The only time I have ever used a kill switch myself is when I had a tipover of a regular motorcycle and it was the fastest way to shut off the engine since the ignition key was located on the side of the bike which was down on the ground.

I had exactly the same thing happen years ago and I was glad to have the kill switch available. But normally I never use, and since owning my RT I don't think I have ever touched it. In fact, when riding recently I accidentally turned the cruise control off and the Spyder slowed down so quickly I thought I had accidentally hit the engine cut-off switch. I would not have minded not having this switch on the RT.

FWIW, I recently took the MSF Basic Riders Class (despite being a motorcyclist for 35+ years; but its a long story as to why I was in that class) the "coaches" insisted that we use the "kill switch" whenever turning off the motorcycles, and then turning the iginition key to off. So a lot of new riders will probably use the switch when they are out riding the roads, thinking that this is the "right" way to turn off the bike. No harm done.

 

[KSCRZR]

The potential consequence of one poorly timed bump of that switch outweighs any dogmatic insistence on its use. I've considered using a drop of epoxy to disable it -- guess I can be overly dogmatic too. But, my decisions only effect me...

I'll admit I have done it, driving it back from Texas when we bought it. Tell you how freaked out I was that something was actually wrong with a bike we just bought and all I did was hit the stupid kill switch. Never have I done it on any other bike I have owned, so don't know if its placement or what with the Spyder. And for reference, I do use it to kill the bike when I park it.

 

[Peacekeeper6]

I don't usually deal with the kill switch when turning my Spyder on and off. It's all done by the ignition key.

However, I use the switch when I'm on my Harley. Don't rightly know why really. But the (possible) eventual failure of the kill switch from countless movements have me thinking that I should do the same when I'm on my 2-wheeler ....

 

[Lew L]

Kill switch?????

.

I've used it a few times-------- looked for one on ALL of our cars or trucks...... ah, NO.

Our :spyder2:'s get more and more like autos without a body. All the electronics. But I'm OK with it being handy.

Lew L

PS: I guess our cars do have a hidden kill switch ( that most people don't know about. In an accident there is a motion switch which shuts off the electronics) usually in the rear of the vehical.

 

[budC]

The "key" word is SWITCH.
This is a MECHANICAL device.
All MECHANICAL device have a limited life expectancy of a certain amount of "cycles".
Those cycles are designated in their design specs and AGE also play into that factor.
So it is not a matter IF but WHEN it will ultimately FAIL.

So you have a choice.
1. Not to use and pretty much never worry
2. Use it and EVENTUALLY find out.

In 56 years on the road, I have never used that switch except ONCE when the bike went down and kept running.
I have seen others that always use that switch. I'm still wondering if they ever got their bikes started or if they are still stranded!

AJ

As someone who did this stuff for a living, all I can say is "it depends"... BUT... the CamAm engineers would have to be incompetent for it to be
a problem. Sure, it can fail, but I can win the lottery, too. The odds are the same order of magnitude.

Switch contact design is really old tech. Like telephone old tech (more than a century old). My first tech job was with a telephone switch manufacturer (North -not Northern- Electric, RIP) and some of the relays (which are just coil operated switches) were designed for thousands of operations per day, and a 25 year life span.

It's not hard to put together switch contacts that will withstand 100K mechanical operations. Make sure they're protected against arcing, and rhodium plated contacts at 12V will make it to 100K electrical operations.

The proof is in the pudding, The number of won't start problems attributable to the kill switch pales compared to almost everything else in the system - ignition modules, wiring, coils, etc, etc, etc.

For convenience, I used the kill switch probably 20% of the time on my ST1100. Never had a problem with it in over 100k mi.

Use it or don't for whatever reason, but switch failure is waaaay down there as a don't-start cause.

 

[budC]

I don't usually deal with the kill switch when turning my Spyder on and off. It's all done by the ignition key.

However, I use the switch when I'm on my Harley. Don't rightly know why really. But the (possible) eventual failure of the kill switch from countless movements have me thinking that I should do the same when I'm on my 2-wheeler ....

There's a reason on 2 wheels - riding with a pillion. I always put both feet down at stops, which means I'm holding the bike with the front brake. Left hand is holding in the clutch. No prehensile nose to grab the ignition switch. Right thumb to the kill switch.

 

[RideOn]

There is another use for the kill switch on a 2-wheeler I haven't seen mentioned. For all the time I rode Harleys, I would use the kill switch to cut off the engine if I parked on a grade. Leave the bike in first gear, kill the engine, let the clutch out, and use the stopped engine as a parking brake. Then turn off the ignition.

On a Spyder, between electric parking brake and SE trans, this is not necessary. So on my RTL, I set the parking brake then turn it off with the key. Kill switch is rarely used.

Different use cases, different results.

 

[Peter Aawen]

There is another use for the kill switch on a 2-wheeler I haven't seen mentioned. For all the time I rode Harleys, I would use the kill switch to cut off the engine if I parked on a grade. Leave the bike in first gear, kill the engine, let the clutch out, and use the stopped engine as a parking brake. Then turn off the ignition.

On a Spyder, between electric parking brake and SE trans, this is not necessary. So on my RTL, I set the parking brake then turn it off with the key. Kill switch is rarely used.

Different use cases, different results.

:agree: - Certainly, there's Different Cases, Different Results :thumbup:

But even so, that bit above is not only 'not necessary', but it won't work on an SE Spyder :lecturef_smilie:

You simply can NOT use the engine as a parking brake on an SE Spyder cos as soon as the engine's stopped there's no oil pressure to keep the clutch engaged on an SE6; or there's no revs to keep the clutch engaged (about 3,300 or so required) on an SE5... which means it'll just roll pretty freely without that electric Parking Brake engaged - hence the bloody strident alarm that goes off for 30 secs if you forget the Park Brake! .

Leaving your SE Spyder in gear with the engine off means the clutch MUST be disengaged & if you've got no Electric parking brake function &/or you aren't using some form of chock/s on a slope, then it's simply a recipie for a run away Spyder!! :yikes:

 

[Isopedella]

Using the kill switch. Do Ya?

I saw this mentioned in another post and decided its better to to start another thread.

After doing a MSF course the member made this comment.

In 50 years of riding I used the "kill switch" 2 times, now I use it all the time.

I didn't want to split the thread so started this.

--------------------------------------------------------------------------------------

I have been riding 50yrs or so too.

I have attended all the rider courses over the last decade with my Son who has completed the program up to advanced rider. He has gone on to do some track days with experienced trainers some of who who have international racing experience.

It was fun so every 3 yrs or so I attend another advanced rider course. Just to be reminded of some things and usually pick up something new. Well worth it.


I have seen some US based videos where everybody stops for a while, shuts the bike down with the Kill Switch but leaves the key on. Then a discussion is had, and they start up and head off again.

Blokes lined up waiting for their turn to complete an activity, like right hand off the throttle and on the tank or your knee and on the idle do extended figure of 8's, thats and scary the first time. All the other remaining riders waiting their turn with the key on and the kill switch engaged.

The thought of insisting that blokes use the switch and leave a bike sitting for periods of time with the Kill Switch off and the key on sickens me.

Specially with these power hungry Spyders.

They do not make that part of our training here in New Zealand. I dont get it.

 

[RangerRick]

In my book using the kill switch, it's to easy to unintentionally leave the key on and guess what dead battery.

 

[K80Shooter]

Any time that I stop the key is removed and put in my pocket. Problem solved about leaving it on.

I guess that's my muscle memory kicking in.

 

[FrogmanDave]

I use the kill switch sometimes at gas stations to keep my bluetooth connected so I don't have to wait the minute or so for it to load again after key off. It is a painfully slow process on these machines. Other than that I never use it.

 

[IdahoMtnSpyder]

I use the kill switch at gas stations to keep the ignition on so I can read the odometer. I put the mileage in my fuel log while I'm pumping the gas. Otherwise I never use it.

 

[narygancy]

Wow, I didn't realize there was such a difference of opinion on this! In 50 yrs of riding 2 wheels I used the kill switch 3 times. When I bought our Spyder, at the urging of a Can Am friend, I took the Can Am course. One of the first things the instructor asked was why I didn't use the kill switch. He explained that somehow it works with the on-board computer to reset everything in proper order. While I have no idea what that means I started using the kill switch and haven't experienced any sort of problem. When I check out Spyder videos on youtube it appears most use the kill switch to shut down. Its a habit for me now.

 

[ButterSmooth]

I'll NEVER forget the day I was cruising down one of our many backroads and decided to flip my 'vents'. When I reached for the right side vent the Spyder suddenly died and I rolled to the shoulder. Keep in mind that this was a very low traffic highway -- maybe 3 cars every 50 miles, or I wouldn't have tried it in motion. As it turned out, my helmet visor hit the kill switch. Can you imagine a similar event (not caused by vent flipping) on a crowded freeway? I was tempted to epoxy the button in the on position.