-
There were many reasons for the change of the site software, the biggest was security. The age of the old software also meant no server updates for certain programs. There are many benefits to the new software, one of the biggest is the mobile functionality. Ill fix up some stuff in the coming days, we'll also try to get some of the old addons back or the data imported back into the site like the garage. To create a thread or to reply with a post is basically the same as it was in the prior software. The default style of the site is light colored, but i temporarily added a darker colored style, to change you can find a link at the bottom of the site.
Scoops kit
- Thread starter jtoro1
- Start date
Highwayman2013
New member
I asked our dealer about it today and he said he would check on it.
Sarge707
Active member
https://drive.google.com/file/d/0B9BFwCzfMWZ8d3dKTC16TnVrNm8/view?usp=sharing
The instructions are at the end of this recall because it is part of it-Page 18-22.
My dealer Got me the kit for $67 and cut the 2 panels for me for $50. I installed.
If your crafty you could figure to cut out a smaller hole (Once you position the scoop) and then once the kit is on the Panel widen the hole out to the proper size BUT your better off with them doing it as they All received templates or having them Just mark the panels for you and you cut and install.
From the picture in (5.) Page 19 you could approximate a slightly smaller hole and if I had to do it over again I would have just cut the hole myself -Slightly smaller and widen later!!!
You basically mark and drill 5 holes on each panel (I did only 4) and screw in the screws from the inside of the panel and screw a couple more pieces on.
Depends on "How Much?" your dealer will work with you or if they just insist on charging $300 Plus for doing a Job most could do quite easily!
The instructions are at the end of this recall because it is part of it-Page 18-22.
My dealer Got me the kit for $67 and cut the 2 panels for me for $50. I installed.
If your crafty you could figure to cut out a smaller hole (Once you position the scoop) and then once the kit is on the Panel widen the hole out to the proper size BUT your better off with them doing it as they All received templates or having them Just mark the panels for you and you cut and install.
From the picture in (5.) Page 19 you could approximate a slightly smaller hole and if I had to do it over again I would have just cut the hole myself -Slightly smaller and widen later!!!
You basically mark and drill 5 holes on each panel (I did only 4) and screw in the screws from the inside of the panel and screw a couple more pieces on.
Depends on "How Much?" your dealer will work with you or if they just insist on charging $300 Plus for doing a Job most could do quite easily!
Last edited:
jtoro1
Member
Thank you for the info I will do it that way. Its not rocket science.
Last edited:
Sarge707
Active member
Glad you got it done! The kits were "Intended" as part of the recall so that's why there's No Instructions and people have to refer to the recall instructions Page 18-22.:congrats:
Troublemaker1
New member
I'd like to order and install these on our 2010, can we buy them yet? The wife has gone through 3 right boots due to the heat melting the glue and allowing the soles to separate. To bad I'll have to remove the moveable air wings that I mounted there.
Sarge707
Active member
You can do 2 things before you even get the kit on your model!
1- Take off the acoustic panels that cover each Cylinder head- There is one on each side and 2 10mm bolts on each.
2- Take off both underneath panels! Most take off the one on the left side when they first change the oil BUT the one on the right side lets out Much more heat than the left side and allows the heat to escape from the Master cylinder area.
3. You don't need the template- When you get the kit it will be obvious what to do and the Recall directions were listed before.. With ALL 3 done your engine will run much cooler and the front of the seat will be cooler.
The Governor
New member
Please send ordering info....
Could you you please get me the contact info of where you ordered the kit? My local guy wants $279, just for the kit. Same part number.
Thanks!
Could you you please get me the contact info of where you ordered the kit? My local guy wants $279, just for the kit. Same part number.
Thanks!
finless
New member
$279 sounds like the cost of the full 2013 recall kit.
A friend of mine is taking his 2012 into the dealer today to get the scoops put on. He is being charged $79 for the kit and 1 hour labor.
Give your dealer the scoop kit part number that is in this post as again he probably just looked up the 2013 recall kit.
Bob
A friend of mine is taking his 2012 into the dealer today to get the scoops put on. He is being charged $79 for the kit and 1 hour labor.
Give your dealer the scoop kit part number that is in this post as again he probably just looked up the 2013 recall kit.
Bob
Troublemaker1
New member
jtoro1
Member
[TD]Can-Am - RT VENT KIT
Item: 219800388
[/TD]
[TD][/TD]
[TD] $50.24 [/TD]
[TD] [/TD]
[/TR]
[/TABLE][/QUOTE]
That's a good deal
Item: 219800388
[/TD]
[TD][/TD]
[TD] $50.24 [/TD]
[TD] [/TD]
[/TR]
[/TABLE][/QUOTE]
That's a good deal
The Governor
New member
Done
Ordered from Powersports Warehouse!
Thank You!
Ordered from Powersports Warehouse!
Thank You!
Similar threads
