p1x tip for two bros

[aka1004]

are you supposed use them rubber rings?
i saw a guy doing it on youtube and it seems he just used one of them on inner side of p1x. i tried installing the tip with rubber ring but it seats kinda funky.:dontknow:

by the way, i think i should have gone with p1... p1x seems too quiet.
it still has good bite when you open it up but seems just little bit too quiet. i will give it a few days since i got used to running without the tip.

 

[chascarpenter1]

I didn't. Get any rubber rings with mine. I did found that it rattled with the excessive space I ended up using some muffler wrap and some gasket seal.

I might contact two brow and see about getting my spacer

 

[aka1004]

I didn't. Get any rubber rings with mine. I did found that it rattled with the excessive space I ended up using some muffler wrap and some gasket seal.

I might contact two brow and see about getting my spacer

i didn't notice it outside but when i brought spyder inside the garage, i did notice high pitch metalic rattling. i guess i was supposed to use them rubber thingy. it came with 2 rubber rings, one thicker than others.
i was wondering if i was supposed to one on each side of p1x.

 

[aka1004]

chascarpenter1, there were other people who did not get the rubber spacers with their tip and two bros sent them the spacers with a phone call.
two bros actually told him not to install the tip until he receive the spacer.

 

[j45p3r]

I couldn't figure out why each tip came with two gaskets (of different sizes). The only thing I could figure was compatibility with different canisters? Either way, both gaskets seemed to work fine on my dual. I ended up using the thicker one (under the tip) and it's been fine. I'll just hang onto the others incase I need them someday.

 

[aka1004]

I couldn't figure out why each tip came with two gaskets (of different sizes). The only thing I could figure was compatibility with different canisters? Either way, both gaskets seemed to work fine on my dual. I ended up using the thicker one (under the tip) and it's been fine. I'll just hang onto the others incase I need them someday.

when i used the gasket, end cap did not seat flush to the muffler.:dontknow:

 

[j45p3r]

when i used the gasket, end cap did not seat flush to the muffler.:dontknow:

I didn't have a problem with that.

 

[aka1004]

I didn't have a problem with that.

didn't the tip kinda float around instead fitting into the slot with the thicker gasket? with thinner one, it barely kept tip from sliding downward.

 

[j45p3r]

didn't the tip kinda float around instead fitting into the slot with the thicker gasket? with thinner one, it barely kept tip from sliding downward.

Nope, it wasn't flush but it was still in there well enough to stay there by itself while I put the end piece back on. Once I tightened the screws down it buttoned up real nice. I wonder if the duals are machined differently than the single?

 

[Smylinacha]

I want to quiet mine down some - I have the tip that isn't the quiet one. It sounds real nice but I want to be able to listen to tunes if I buy a Cranker Tank Bag.

 

[aka1004]

I want to quiet mine down some - I have the tip that isn't the quiet one. It sounds real nice but I want to be able to listen to tunes if I buy a Cranker Tank Bag.

hey may be we can swap?
i am gonna give it a day or two but it seems this one is too quiet for me.

 

[chascarpenter1]

I contacted two Bros about my missing gaskets they said they would send me some. I also asked about the spring mount being on the wrong side of the mid pipe they asked me to take a picture and send it to them which I did yesterday. Hopefully they will send me a new mid pipe or better yet a new unit.

 

[Smylinacha]

hey may be we can swap?
i am gonna give it a day or two but it seems this one is too quiet for me.

Cool! Let me know!