Changing front fender marker light. 2015 RT

[WARWAGON]

How do you change fender marker light on a 2015 RT? Must have missed in manual.

 

[BLUEKNIGHT911]

??????????????

How do you change fender marker light on a 2015 RT? Must have missed in manual.

Are you talking about the " TIP " light on the Basic style fender ??????.....................Mike :thumbup:

 

[WARWAGON]

Are you talking about the " TIP " light on the Basic style fender ??????.....................Mike :thumbup:

Yes that's the one. Do you have to remove wheel?


Sent from my iPhone using Tapatalk

 

[bmwlarry]

You need to use something like a flat screwdriver or your fingers if you can and push the clear plastic cover back and up. Reverse for install. be careful the little black gasket kind of thing is tricky

 

[cuznjohn]

you have to remove the wheel, then you can get to everything from underneath

 

[Bob Denman]

You need to use something like a flat screwdriver or your fingers if you can and push the clear plastic cover back and up. Reverse for install. be careful the little black gasket kind of thing is tricky

:agree: There's no need to remove the wheel, when this is all happening to the "Old-Style" fender. :thumbup:

 

[WARWAGON]

You need to use something like a flat screwdriver or your fingers if you can and push the clear plastic cover back and up. Reverse for install. be careful the little black gasket kind of thing is tricky

Thanks. Will give it a try.


Sent from my iPhone using Tapatalk

 

[SpyderAnn01]

Warwagon's signature says that he has a 2015 RTS SE6 Limited (not sure exactly what that is - an S or a LTD?) so he does not have the old style fenders. If that is the case remove the wheel will give you the access you need to change the tip light.

 

[Bob Denman]

Thanks Ann!
When he responded to Mike; it seemed as if he was saying that he had the old style fenders. pps:

Good catch, and remove the wheel! :thumbup:

 

[Doc - Riverside]

How do you change fender marker light on a 2015 RT? Must have missed in manual.

The White front marker light is a sealed LED unit. You can't change the color. Basically there are two High Intensity White LED that shine into light pipes to illuminate the front fender. Is it burned out?

 

[WARWAGON]

The White front marker light is a sealed LED unit. You can't change the color. Basically there are two High Intensity White LED that shine into light pipes to illuminate the front fender. Is it burned out?

Not sure. Just does not light up. Was flickering for awhile. But now nothing. Back to dealer. Less than year old.


Sent from my iPhone using Tapatalk

 

[CapeSpyder]

On the new fenders, i found taking off the fender was easy. 4 bolts and unplug then you can remove the channel with ease and get to all the wires

CapeSpyder
Sent From my Note 5

 

[BLUEKNIGHT911]

NOT TIP LIGHT !!!!

Not sure. Just does not light up. Was flickering for awhile. But now nothing. Back to dealer. Less than year old.


Sent from my iPhone using Tapatalk

Mea Culpa - I didn't look down far enough :gaah:....... Since it's in warranty I would have the dealer fix it .....it could be a wiring issue .....sometimes ( like rear fender area of early GS/RS ) it comes loose or was never properly fastened ........Mike :thumbup:

 

[WARWAGON]

Mea Culpa - I didn't look down far enough :gaah:....... Since it's in warranty I would have the dealer fix it .....it could be a wiring issue .....sometimes ( like rear fender area of early GS/RS ) it comes loose or was never properly fastened ........Mike :thumbup:

Started a case with dealer. Won't fix it until it completely stops working. So until then drive around with it flashing off and on.


Sent from my iPhone using Tapatalk

 

[cptjam]

Check

Look at the connection. Unplug, plug back in. Inspect the wire, look for wear, breaks, cuts. Jiggle the wire, try to make it blink. If you are up for it, unplug, put a voltmeter on, see if the problem is upstream. Normally, a tiny cut is all it is. Finding it is the tough part! Good luck. Joe

 

[WARWAGON]

Look at the connection. Unplug, plug back in. Inspect the wire, look for wear, breaks, cuts. Jiggle the wire, try to make it blink. If you are up for it, unplug, put a voltmeter on, see if the problem is upstream. Normally, a tiny cut is all it is. Finding it is the tough part! Good luck. Joe

Thanks squealer check that all and could not find it. So still waiting for complete failure.


Sent from my iPhone using Tapatalk