2015/16 RT-S Side Marker LED question

[Hokiev]

(Now that I have purchased a new RT, I know the answer is as posted below, they DO NOT have lighted LED's. The reference in the literature is referring to what used to be called front tip lights, which are longer LED's now.)

I had a 2011 RT LTD which I sold several years ago. That model had REFLECTOR markers on the side of the fenders. I know there are aftermarket LED lights that could be installed to replace the REFLECTORS and you could also add a module so the will blink when using the turn signal.

I am looking at possibly purchasing a 2015 or 16 RT-S. Looking at the literature it appears the fenders now have LED side marker lights standard. If that is the case, do they blink with the turn signals?

If they don't, is there a module you can buy that would allow them to blink and is it a special module that works specifically for the newer models or do you use the same module that you would buy for the older non stock side marker LED's?

Are they hard to install and do you have to cut through any existing parts on the Spyder or are they plug-and-play?

Thanks in advance for any information.

 

[Bob Denman]

The new "evolved" fenders are still just equipped with reflectors from the factory.
But TricLEDs makes some VERY nice lighting kits for them! :thumbup:
http://www.tricledusa.com/#!home/mainPage

 

[BLUEKNIGHT911]

FENDER LED's

.....I believe another site sponsor ....VALUE ACCESSORIES....sells the same thing for less.....check the Home page for their AD.......Merry Christmas .......Mike :thumbup:

 

[Trbayth]

I just installed that kit on my ST. They look great but there's isn't a lot of room inside the front of the channel where the lights and wiring are; the bracket for the fender it self is in the way.

I'm planning on re-wiring them myself over the winter for a neater look.

 

[Bob Denman]

Thanks, Mike; I wasn't aware of their products. :thumbup: I'm just more familiar with Reggy's.
Merry Christmas, to you and yours!

 

[Deanna777]

Amber/Red front Fender LED'S and Red Side Marker LED'S @ night

Here is a picture of the Amber and Red Fender LED Lights with safety Reflector Design ( on a 2014RTS-SE6 Cognac) @ night:

This is a picture with Amber and Red Front Fender LED'S lights with the Safety Reflector design and Red Side Marker lights at night

with the Safety Reflector Design on a 2014RTS-SE6. I bought these @ TRICLED.com a vendor on this site. Deanna

 

[Cruzr Joe]

Spyderpops also has the fender lights that are curved to better fit the fender tops

Cruzr Joe

 

[Hokiev]

Confused!

I am still confused. The CanAm web site for the 2016 indicates this:

An intense look from low-profile tires wrapped around 12-spoke carbon black satin wheels, and premium front fenders with integrated LED light pipes. The Spyder RT-S model also includes a host of Satin Chrome accents and two-tone black/charcoal seat for a striking look.

So what is the "Front Fenders with integrated LED light pipes" referring to? Are those just the front tip lights?

 

[Copperman]

I just installed that kit on my ST. They look great but there's isn't a lot of room inside the front of the channel where the lights and wiring are; the bracket for the fender it self is in the way.

I'm planning on re-wiring them myself over the winter for a neater look.

The key is to drill a hole in the "brace" and pass the wires through to the front. It's just plastic and the wires will fit like they belong.

 

[Devious56]

On my 2015 RT Limited, the White LED's on the front of my front fenders are running lights, and no, they do not flash with the turn signals. Value Accessories also has a set of fender lights made by Custom Chrome that are a bit different than the TricLED ones, and those are the ones I'm going to try in the near (?) future.

David

 

[SpyderAnn01]

Thanks, Mike; I wasn't aware of their products. :thumbup: I'm just more familiar with Reggy's.
Merry Christmas, to you and yours!

Value Accessories sells Tric-LED lights at a discount

 

[SpyderAnn01]

I am still confused. The CanAm web site for the 2016 indicates this:

An intense look from low-profile tires wrapped around 12-spoke carbon black satin wheels, and premium front fenders with integrated LED light pipes. The Spyder RT-S model also includes a host of Satin Chrome accents and two-tone black/charcoal seat for a striking look.

So what is the "Front Fenders with integrated LED light pipes" referring to? Are those just the front tip lights?

The front marker light is LED so they aren't completely crazy. Don't know what a light pipe is though sounds like someone might be smoking something in a pipe. :roflblack:

 

[Bob Denman]

Perhaps it's the French-Canadian, to English translation; that they outsourced to a company in Bangladesh.


Dee,
GREAT pictures of the side lighting on your bike!! :clap: :firstplace:

 

[jcthorne]

If you look closely at the front fender tip led lights with them on, you will see clear plastic ridges running the length of the lamp housing that light up from the LED behind. Those are commonly referred to as light pipes. They carry the light from the LED to the rest of the lense so it appears to light up the entire length.

 

[Deanna777]

Perhaps it's the French-Canadian, to English translation; that they outsourced to a company in Bangladesh.


Dee,
GREAT pictures of the side lighting on your bike!! :clap: :firstplace:

Bob, THANKS I need to add "The Pictures" to my Album. Deanna

 

[Deanna777]

The Tric LEDS front Amber/Red fender Led's with the safety reflector design + Red Rear Side marker with the safety reflector design comes with instructions for " Do It your self installation ". Deanna

 

[Trbayth]

The key is to drill a hole in the "brace" and pass the wires through to the front. It's just plastic and the wires will fit like they belong.

Yep did that. That's not the issue. There's very little room by the front tip lights due to the bracket for the fender itself.

Two taps for the existing wires plus two spade plugs for the side and rear lights really don't fit well.

 

[Bob Denman]

:shocked: I don't believe that I used the taps up front...
Just cleaned off some coating, soldered it, and taped it up! :thumbup:

 

[Copperman]

Yep did . That's not the issue. There's very little room by the front tip lights due to the bracket for the fender itself.

Two taps for the existing wires plus two spade plugs for the side and rear lights really don't fit well.

In that case... Never mind!

I installed mine using posi-taps. It was a little snug but it worked.

 

[trikermutha]

Mine are soldered to a adapter plug that just plugged into the existing wire harness. No drilling ,cutting. They can be removed and put back to stock if I wanted too..:thumbup: