-
Sequentil arrow turn signals.
l
I have truly looked and can not find a site or Auto parts store that has sequential turn signals. I would like the ones that fit inside the side mirror and have an arrow that points in the direction you are turning. I think I just have to lift the mirror straight up. Is that correct. A link will be appreciated.
-
Sequential
Forgot to mention I have a RT S SE LIMITED. I know someone will as that. Thanks
-
Registered Users
Try Here
Originally Posted by SPYDERFUZZ
l
I have truly looked and can not find a site or Auto parts store that has sequential turn signals. I would like the ones that fit inside the side mirror and have an arrow that points in the direction you are turning. I think I just have to lift the mirror straight up. Is that correct. A link will be appreciated.
Try here......http://www.tricled.com/TricLed.com/Home.htm
Illegitimi non Carborundum
2013 RT-S Circuit Yellow with Black Trailer
-
Registered Users
Originally Posted by SPYDERFUZZ
l
I have truly looked and can not find a site or Auto parts store that has sequential turn signals. I would like the ones that fit inside the side mirror and have an arrow that points in the direction you are turning. I think I just have to lift the mirror straight up. Is that correct. A link will be appreciated.
iJDMtoy.com These are much better than Tricled.
-
Registered Users
2012 White RT Limited and 2013 Yellow ST-S Think 3 .i.
-
Active Member
turn signal arrows
I really like the idea but how would you install this on an RT mirror? They're not too easy to disassemble without breaking plastic retaining tabs etc. I would probably need a video or very clear and precise instructions for the Spyder. Some pretty neat stuff on iJDMtoy.com site. Thanks for posting it RTVIPER.
Last edited by Olddood; 09-08-2013 at 01:34 PM.
-
Registered Users
I installed them on my 11. They are awesome!!!
-
Active Member
Did you have trouble
[QUOTE=RTVIPER;685677]I installed them on my 11. They are awesome!!!
Did you have any trouble getting the mirror off the plastic around it? Any advice if I would do mine.
-
Originally Posted by RTVIPER
I installed them on my 11 . They are awesome!!!
Just ordered the amber ones from iJDMtoy.com....
Any advice or wisdom to share? Don't suppose you have pics?!
Thanks! They look awesome and once installed, I will be able to see if I forgot to cancel them.
Not to mention let others know that I'm turning/lane changing!
Can you say "SAFETY FARKLE"?
-
Active Member
Sequential turn signals
Thanks for posting the video. While I can see that it's pretty slick, it would seem to me that if you use these at night, you wouldn't be able to see anything in the mirror, due to night vision loss.
Is that even an issue?
-
Trun Signal
They go on the back of the mirror
I got the web site but can find the right page to order
-
Originally Posted by SPYDERFUZZ
They go on the back of the mirror
I got the web site but can find the right page to order
When you get to their website, just type in sequential turn signal and it should take you right to them!
-
Very Active Member
VISION IN MIRROR
Originally Posted by mooneych
Thanks for posting the video. While I can see that it's pretty slick, it would seem to me that if you use these at night, you wouldn't be able to see anything in the mirror, due to night vision loss.
Is that even an issue?
I had the same thoughts, and am thinking of putting a piece of aluminum foil on the bottom half , so only the top half blinks in the sequence.....since it would still be one inch high I think I would still notice it.......I have an RSS and the mirror is smaller so this is a consideration........Mike...
-
Originally Posted by SPYDERFUZZ
They go on the back of the mirror
I got the web site but can find the right page to order
What do you mean they go on the back of the mirror?
Love my
Statistics show that most motorcycle accidents are caused by a defective nut holding the handlbars.
-
Registered Users
I took a heat gun and GENTLY heat up the mirror to separate it. I used a paint scraper to separate, re-heating as needed. Once separated, I removed the section of glue (on back of glass)where the LED would sit. Used some 3M double sided tape (as thin as I could get). Put it close enough to just hold the LED in place. The remaining glue you didn't scrape should be enough to re-stick. I used the heat gun on the 3M tape and remaining glue to make real sticky. Stuck back like new. You'll have to drill a small hole to feed the wires to connect to signal wires (I used the first 6 steps of the installation instructions from the MUTH website http://shop.muthco.com/content/pdf/i...m%20Spyder.pdf )
Last edited by RTVIPER; 09-09-2013 at 11:28 PM.
-
Active Member
-
Registered Users
-
Registered Users
-
Teddys favorite human
No, night brightness is NOT an issue at all
Last edited by CyncySpyder; 09-13-2013 at 09:10 AM.
-
Very Active Member
Is the glass available as a separate part from CanAm or only the whole assembly? I was already nervous about this install.
-
Teddys favorite human
Don't have this answer for sure, I'd suggest contacting your dealer
-
Very Active Member
THE GLASS
-
...Consult your Bank manager before going to the toolbox...
-
Registered Users
-
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|