Results 1 to 19 of 19
  1. #1
    Member
    Join Date
    Oct 2020
    Location
    NW INDIANA
    Posts
    12
    Spyder Garage
    0

    Default Should I lubricate grommet?

    I just installed a new sway bar on my new to me 2015 RT yesterday. I got a lot of guidance from a youtube video by Can-Am Spyder Accessories. In the video the installer suggested spraying "a little white grease" on the grommets that hold the snap on panels in place thus making it easier to remove these panels next time. When I changed engine oil a month ago I lubed the grommets with a little shot of Windex and everything glided back into place smoothly but I removing a couple of those same panels yesterday and it was a struggle.
    The question is, should I follow the video tip and put a grease on the grommet and probably collect dirt or just leave it factory dry and threated to break off panel tabs with each removal.
    You folks on this forum have lots of practical experience that I might as well tap into, even if my question is pretty trivial.

  2. #2
    Active Member Valkrocket's Avatar
    Join Date
    May 2018
    Location
    Murrells Inlet, SC
    Posts
    139
    Spyder Garage
    1

    Default

    I find grease on the grommets make for much easier removal and reinstallation of the panels. Also keeps them from drying out and eventually tearing and breaking. Not a trivial question.
    GLIDE-ON>>>>>>>>>>>>>>


    "Blue Belle" 2021 RTL Chrome in Petrol Blue
    2021 RTL Chrome , Petrol Blue

  3. #3
    SpyderLovers Ambassador Little Blue's Avatar
    Join Date
    Sep 2017
    Location
    Indiana USA
    Posts
    4,127
    Spyder Garage
    1

    Default Lite Film

    I have used a very lite film of grease on the 'tabs'. Remember less is best. Some people have said that they have issues with the panels coming off 'ryding on the road'.

    Good Luck on Your Mission. .....
    My Spyder .....'Little Blue-Boy'
    2016 RT Limited , Orbital Blue

  4. #4
    Active Member Snoking1127's Avatar
    Join Date
    Oct 2020
    Location
    Arizona
    Posts
    196
    Spyder Garage
    0

    Default

    I shoot a little 3M Aerospace 303 on mine. I have used it on tires for years and on our boats for anything plastic or rubber. Use it on the dash and interior of vehicles, and have never had a cracked dash. It is pretty universally recommended to NOT use petroleum products on rubber. If you use grease maybe it should be a synthetic grease. Aerospace 303 seems to do the job well. They go on easy and later come off OK(not fall off ok), and not hard to get off like RedRover's Windex experience.

    Windex® Original Glass Cleaner
    Water Water. Provides a liquid base for a product.
    2-Hexoxyethanol Cleaning Agent. ...
    Isopropanolamine Cleaning Agent. ...
    Ammonium Hydroxide Cleaning Agent. ...
    Lauryl Dimethyl Amine Oxide Wetting Agent. ...
    Sodium Dodecylbenzene Sulfonate Wetting Agent. ...
    Fragrance Fragrance. ...
    Liquitint® Sky Blue Dye Dye.

    Several of these items are not good for rubber.

    Chris
    2018 RT Limited Chrome - Champagne Metallic - East Valley of Phoenix

    Magic Mirrors, 360 LED head lights, dual USB with volt meter, GPS, phone and drink holders, Formoza's, BajaRon sway bar, dash cam, foam grips, 7 Jurock WS, Ikea sheep skin, HW pegs and driver back rest.

  5. #5
    Active Member spyder01's Avatar
    Join Date
    May 2018
    Location
    millsboro,delaware
    Posts
    305
    Spyder Garage
    0

    Default

    Way too many people have had the panels fly off at high speed so I would recommend spitting on the grommet for lube,it will dry and then be less likely to come off.
    2017 RTL ORBITAL BLUE

  6. #6
    Very Active Member JayBros's Avatar
    Join Date
    Jul 2014
    Location
    Mint Hill, NC
    Posts
    4,675
    Spyder Garage
    0

    Default

    Ann Meyer of Squared Away tipped me off to the Windex spritz a number of years ago and I'm a firm believer in it. It dries very quickly and the grommets then have a tight grip on the pins. I don't believe in grease of any kind on them.
    Artillery lends dignity to what would
    otherwise be a vulgar brawl.
    ******************************
    Cognac 2014 RT-S

  7. #7
    Very Active Member Grandpot's Avatar
    Join Date
    Oct 2014
    Location
    Fort Mill, SC
    Posts
    1,913
    Spyder Garage
    0

    Default

    With grease it's: Easy on - Easy fly off. Do what JayBros said.
    2011 RTS
    1998 Honda Valkyrie
    US Navy Veteran
    SC Law Enforcement Boat Captain
    CNC Machine Service Technician
    President: Rolling Thunder SC1
    Member: Disabled American Veterans, Rock Hill, SC
    Member: American Legion
    Experience is recognizing the same mistake every time you make it!

  8. #8
    Very Active Member RICZ's Avatar
    Join Date
    Feb 2019
    Location
    Portland, Oregon
    Posts
    1,801
    Spyder Garage
    1

    Default

    I wouldn't do it. I lubed grommets on a previous bike with a silicone lube and I had to buy new grommets.
    Ours is a red, black and chrome 2017 F3 Limited. Bought new in 2/2019. The avatar is my first bike back in 1952, a Simplex Servi-Cycle. Photo taken at the Barber Museum.
    2017 F3 Limited , Red, Black & Chrome

  9. #9
    Active Member
    Join Date
    Nov 2018
    Location
    N.E. Ohio
    Posts
    494
    Spyder Garage
    0

    Default

    With all due respect, I have been using a silicone lube product for years with no problems on rubber and plastic items with nairly a problem. Maybe a different product than others have used. It works for me and protects the said items from weather cracking. cueman

  10. #10
    Very Active Member RICZ's Avatar
    Join Date
    Feb 2019
    Location
    Portland, Oregon
    Posts
    1,801
    Spyder Garage
    1

    Default

    Quote Originally Posted by cueman View Post
    With all due respect, I have been using a silicone lube product for years with no problems on rubber and plastic items with nairly a problem. Maybe a different product than others have used. It works for me and protects the said items from weather cracking. cueman
    Me too. I was surprised when my grommets got trashed after applying a silicone lube. There must have been something it.
    Ours is a red, black and chrome 2017 F3 Limited. Bought new in 2/2019. The avatar is my first bike back in 1952, a Simplex Servi-Cycle. Photo taken at the Barber Museum.
    2017 F3 Limited , Red, Black & Chrome

  11. #11
    Very Active Member JayBros's Avatar
    Join Date
    Jul 2014
    Location
    Mint Hill, NC
    Posts
    4,675
    Spyder Garage
    0

    Default

    I've a can of silicone spray but just never considered using it because the Windex is closer. My objection is to any kind of petroleum lubrication product. Changed oil and filter last week and got a good look at the grommets; all are in good shape after 6+ years and 70K+ miles.
    Artillery lends dignity to what would
    otherwise be a vulgar brawl.
    ******************************
    Cognac 2014 RT-S

  12. #12
    Very Active Member Fatcycledaddy's Avatar
    Join Date
    Jul 2015
    Location
    Dorr, michigan
    Posts
    1,176
    Spyder Garage
    2

    Default

    Windex, spray wax or detailer all work much better than a lube that will stay there and attract dirt and dust. IMHO
    2020 RT Limited , Petrol Blue

  13. #13
    Very Active Member ThreeWheels's Avatar
    Join Date
    Feb 2010
    Location
    Danbury Connecticut
    Posts
    3,118
    Spyder Garage
    0

    Default

    No question is trivial.
    There's no such thing as a stupid question. Only stupid answers.

    Your original choice of using windex is, in my opinion, one of the best imaginable.
    The panels go in easy but they're hard to come off.
    That's the way it should be.

    If you search the forum, you'll find NUMEROUS posts (including mine) of people who had to spend good money replacing panels that fell off after simply hitting a bump.
    Some of us, including me, actually installed velcro to the panels to be sure they only came off when you needed them off.

    So, in my opinion, it's good to put some kind of lubricant on the grommets when installing the panels, but you want a lubricant like windex or some other soap that will dry up and go away so that the grommets will hold the panels firmly after installation.
    I always just used spit....................
    If you use a grease, then it's easy on, but way too easy OFF.

    Just my opinion. I could be wrong, and It's a moral certitude that someone on this forum will let me know if I am.
    My Gas Tank Is Full; My Bladder Is Empty
    Time To Motor On
    IBA #47122

  14. #14
    Active Member
    Join Date
    Nov 2018
    Location
    N.E. Ohio
    Posts
    494
    Spyder Garage
    0

    Default

    “The panels go in easy but they're hard to come off.” Hey ThreeWheels, you just got me to thinking. How about hand sanitizer? I just used it the other day on my hand grips! cueman

  15. #15
    Active Member Snoking1127's Avatar
    Join Date
    Oct 2020
    Location
    Arizona
    Posts
    196
    Spyder Garage
    0

    Default

    Quote Originally Posted by cueman View Post
    “The panels go in easy but they're hard to come off.” Hey ThreeWheels, you just got me to thinking. How about hand sanitizer? I just used it the other day on my hand grips! cueman
    You must of purchased it before covid-19 arrived. Try to find it now? That is why I used Aerospace 303 to install my foam hand grips. They do not move at all once I got them installed.
    2018 RT Limited Chrome - Champagne Metallic - East Valley of Phoenix

    Magic Mirrors, 360 LED head lights, dual USB with volt meter, GPS, phone and drink holders, Formoza's, BajaRon sway bar, dash cam, foam grips, 7 Jurock WS, Ikea sheep skin, HW pegs and driver back rest.

  16. #16
    Very Active Member JayBros's Avatar
    Join Date
    Jul 2014
    Location
    Mint Hill, NC
    Posts
    4,675
    Spyder Garage
    0

    Default

    I agree with ThreeWheels but only used spit once; have better aim with Windex. IMO you absolutely want the panels to be hard to pull out of the grommets.

    I used hand sanitizer about five years ago to install my grips and they haven't moved at all. It was recommended by the vendor, but again I think Windex would be easier.
    Artillery lends dignity to what would
    otherwise be a vulgar brawl.
    ******************************
    Cognac 2014 RT-S

  17. #17
    Very Active Member troop's Avatar
    Join Date
    Aug 2019
    Location
    Stoughton, WI
    Posts
    1,198
    Spyder Garage
    1

    Default

    A little bit of saliva applied with a finger tip. Done ...


    2019 F3-S SE6 Monolith Black
    --------------------------------
    Comfort: Madstad 14" dark gray - 20" light gray windshields/Seth Laam seat/Homemade floorboards-highway pegs/+4 and +5 linkage/Attitude bars/Heated grips/Big Bike rider backrest

    Ride and Handling: Spyder Extras sway bar/Vredestein Q5 front tires/Cooper CS5 Ultra rear tire/Two Up shock/Laser aligned/15" Widow PPA wheels

    Performance: DynoJet PV3 (custom mapped by Fuel Moto)/K&N air filter/Baldwin cat delete pipe/Lamonster belt roller/Pedal Commander/EBC HH brake pads

    Convenience: Shad detachable luggage/Top Cuff w/handlebar mirrors/Garmin Zumo XT GPS/Lamonster Packrack-Kappa 56L top case

    Safety/Protection: H4 LED headlights/Aux rear LED lights/TricLED driving lights/TricLED run-brake-turn rear light/Frunk lip LED light strip/Spyder Extras bumper guard grill
    2019 F3-S , Monolith black

  18. #18
    Active Member RideOn's Avatar
    Join Date
    Sep 2018
    Location
    Bakersfield, CA
    Posts
    74
    Spyder Garage
    3

    Default Agree with hand sanitizer

    Quote Originally Posted by JayBros View Post
    I agree with ThreeWheels but only used spit once; have better aim with Windex. IMO you absolutely want the panels to be hard to pull out of the grommets.

    I used hand sanitizer about five years ago to install my grips and they haven't moved at all. It was recommended by the vendor, but again I think Windex would be easier.

    I've had good luck with hand sanitizer too. Wet, parts just slip into place. Once it dries, the attachment is firmly in place with no slipping.
    “There comes a time in the affairs of men... when we must seize the bull by the tail and face the situation.” - W.C. Fields

    2019 Spyder RT Limited
    Asphalt Gray/Chrome

    Recently departed:
    2014 Spyder ST SE5
    Steel Black Metallic
    2019 RT Limited , Asphalt Gray/Chrome

  19. #19
    Very Active Member
    Join Date
    Sep 2016
    Location
    Chillicothe, Oh.
    Posts
    788
    Spyder Garage
    1

    Default

    Quote Originally Posted by troop View Post
    A little bit of saliva applied with a finger tip. Done ...
    2015 RT , Black

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •