Well I could not make it home with that pulley

[aka1004]

I was on my way home from la and belt/gave out on freeway. Belt is all chewed up. EnginE is on tranny engages but no forward movement.
Where is this AAA truck...

 

[docdoru]

I wonder why...:dontknow:

 

[DynamoBT]

Hopefully you get help soon. And can get home soon too.

 

[Longlegs]

That sucks. Do you have a dealer located to fix it? I can't remember how far you are from home.

 

[bjt]

Is it the belt that gave out or the pulley? Either one is bad but I'd rather replace a belt than the pulley.

 

[aka1004]

I took a closer look and bolt is turning but pulley is not. I also see belt has melted plastic looking pieces hang on it.

 

[bjt]

So both are bad.... That really stinks. Hopefully you have a good dealership to work with.

 

[SpyderWolf]

Wow, that truly stinks. I hope they are able to get you fixed up, and back on the road, quickly. Best of luck.

 

[fastfraser]

Sorry to hear about your trouble ! What year and model do you have and how many miles ?

 

[aka1004]

Sorry to hear about your trouble ! What year and model do you have and how many miles ?

09 se5 with 31600

 

[krb1945]

Has anyone seen the...

service bulletin and the updated bolt torque setting?

One would think this bolt would be on every 12000 mile service to be torqued. Heating, cooling and vibration will loosen any bolt or fastener no matter how good the scotch grip or locktite. //Ken

 

[boborgera]

service bulletin and the updated bolt torque setting?

One would think this bolt would be on every 12000 mile service to be torqued. Heating, cooling and vibration will loosen any bolt or fastener no matter how good the scotch grip or locktite. //Ken

Or Duct tape.:joke:

 

[boborgera]

I wonder why...:dontknow:

Don't know much about belts, This is the first bike ive had with a belt.
I do know if you tighten a chain too tight they can and sometimes do snap.
If I'm not mistaken a belt is much stronger than a chain so something has to give if the belt is too tight. Every Spyder I've seen on a showroom floor seems [to me] to have the belt way too tight. :dontknow:

 

[krb1945]

Lamont suggested many months...

ago that there was too much tension on these drive assemblies when received from the dealers. When aligning my belts "off" the inner lip of the rear sprocket I also reduced the belt tension to the range of 220 to 260. When you get right down to the nuts and bolts of this system 260 is still quite a bit of tension. I tried lowering it to the 180-220 range but found a lot of vibration on the testing so I increased it back to the 220 to 260 range. At that range it is smooth as silk. /Ken

 

[Lamonster]

ago that there was too much tension on these drive assemblies when received from the dealers. When aligning my belts "off" the inner lip of the rear sprocket I also reduced the belt tension to the range of 220 to 260. When you get right down to the nuts and bolts of this system 260 is still quite a bit of tension. I tried lowering it to the 180-220 range but found a lot of vibration on the testing so I increased it back to the 220 to 260 range. At that range it is smooth as silk. /Ken

220-240 seems to work just fine for me, very little vibration and there is no way you're going to skip a tooth with that much belt wrap.

 

[JkRbbt]

Been following Spyder sites for several months now. I guess this is one BIG question I have. When you have a roadside problem as described here, you can call AAA and take it WHERE?? With a H/D or Honda or... you can find dealers, or at least mechs familiar with your bike, most places. Who services or is familiar with BRP products? Am I gonna be stranded a LOOOONG way from home! FedEx ain't cheap!! :yikes: I appreciate your input! Thanx!

Loren

 

[boborgera]

AAA gave me a lot of run around with towing. I hope brp does not...
I have aaa premier with 200 mile tow but was not told it's only 100 miles for rv and motorcycle. I was still 150 miles out but aaa driver gave me an idea to go 100 miles with him to ca/nv stateline and call aaa again for another tow. He said aaa from ca can not go into nv anyway. So i called for 2nd tow, after talking to few different people with different excuses(thus area is served by northern cal aaa and they don't have the equipment to tow motorcycle, Nevada aaa does not tow motorcycle than I was handed over to aaa insurance claims for whatever the reason, etc) they finally agreed to tow the spyder to las Vegas.

I have foremost insurance with free towing, Plus AMA W/towing Never had to use either ray: But they both specialize in towing motorcycles.
I also have AAA Plus. I Would use them for my car/truck.
Many years ago when my car needed a tow AAA wanted to tow my car there shop,
I gave the driver a few extra bucks and he towed me home.

 

[aka1004]

Been following Spyder sites for several months now. I guess this is one BIG question I have. When you have a roadside problem as described here, you can call AAA and take it WHERE?? With a H/D or Honda or... you can find dealers, or at least mechs familiar with your bike, most places. Who services or is familiar with BRP products? Am I gonna be stranded a LOOOONG way from home! FedEx ain't cheap!! :yikes: I appreciate your input! Thanx!

Loren

this is my 3rd time being stranded on my spyder and the furthest, 150 miles and yes you do have to take spyder to a spyder dealer.
i guess i am lucky to live in right part of country where there are plenty Spyder dealership around but would be better if it does not happen...
if i am stranded on a long distance trip in some remote area with no celphone signal...


anyway spyder is in the shop, same problem with pulley as other's plus when pulley snapped out of it's place, it chewed up the belt and gps. waiting to hear from dealer when parts can get here and if brp is denying coverage under warranty.

 

[asmdjackal]

I took a closer look and bolt is turning but pulley is not. I also see belt has melted plastic looking pieces hang on it.

If the pulley is shot.. you might try one of the MMG 30 tooth front pulleys. Lower your highway RPMS a bit...

 

[3Ryder]

Adjusting Belt Tension

ago that there was too much tension on these drive assemblies when received from the dealers. When aligning my belts "off" the inner lip of the rear sprocket I also reduced the belt tension to the range of 220 to 260. When you get right down to the nuts and bolts of this system 260 is still quite a bit of tension. I tried lowering it to the 180-220 range but found a lot of vibration on the testing so I increased it back to the 220 to 260 range. At that range it is smooth as silk. /Ken

What procedure is followed to adjust the tension and what tools are necessary?