Spyder Harley

[HD2CANAM]

While still "fighting" to put the 4" NM riser on (Reverse Gear), I ran across some old parts from a Harley I owned years ago. It was a gas cap with a Spider engraved in it. I tried it and it works perfect, so now I have a Harley Spyder. Well sort of?:dontknow:

 

[tatt2r]

had no problems installing risers and i did mine in a dark cold garage in the middle of the night with spot lights on and an electric heater.... took about 2 hours ... you must be trying to do something that is wrong...
but the gas cap sounds cool too bad it's under seat

 

[LDFIREWORKS]

SOUNDS PRETTY COOL SEND PICS:dontknow:

 

[HD2CANAM]

had no problems installing risers and i did mine in a dark cold garage in the middle of the night with spot lights on and an electric heater.... took about 2 hours ... you must be trying to do something that is wrong...
but the gas cap sounds cool too bad it's under seat

I definitely am not a mechanic, but I did install the back rest and passenger footpegs. My problem is on the clutch side (SM5) 2009. In Lamonster's install, it sounded simple. The problem I am having now is with the reverse. Everytime I try to put the lever in, the cable end keeps popping out.La monster also mentioned something about a slot in the bar to locate the control housing. I see a slit, but cannot see what it does. I am at the point now where I don't even remember if the clutch lever goes on 1st or the reverse gear setup. HELP!!!

 

[tatt2r]

I definitely am not a mechanic, but I did install the back rest and passenger footpegs. My problem is on the clutch side (SM5) 2009. In Lamonster's install, it sounded simple. The problem I am having now is with the reverse. Everytime I try to put the lever in, the cable end keeps popping out.La monster also mentioned something about a slot in the bar to locate the control housing. I see a slit, but cannot see what it does. I am at the point now where I don't even remember if the clutch lever goes on 1st or the reverse gear setup. HELP!!!

the notch needs to be in front if you put the two pieces of the controles together and leave them loose and turn the new handle bar end forward or back you will feel the controle click into the notch in the bar

 

[HD2CANAM]

I posted in another location, but thanks to all of you supportive people it is on and working. I now needed hand grips since I had to cut off one of the old ones. I looked at Dennis Kirk and JP Cycles as someone suggested, but did not find anything. I ran across Hoprodox while browsing and had never heard of before and found a set with spider web markings on them. Expensive, but am getting used to this, so ordered a set.

 

[HD2CANAM]

SOUNDS PRETTY COOL SEND PICS:dontknow:

I will try

 

[SpyderDeb]

Nice gas cap! I tried to find the Hoprodox grips that you mentioned on the net - and failed :dontknow: - would you post the website please. Thanks!

 

[M2Wild]

I will try

Hey ... that looks pretty slick.:thumbup:

 

[HD2CANAM]

Nice gas cap! I tried to find the Hoprodox grips that you mentioned on the net - and failed :dontknow: - would you post the website please. Thanks!

I sent you a email, but it is xoprodux.com/, sorry for the typo. pps:

 

[TJ_Spyder]

I sent you a email, but it is xoprodux.com/, sorry for the typo. pps:

Double typo!

http://www.xoprodox.com/

 

[effgjamis]

http://www.xoprodox.com/

Check out the ball bearing throttle assembly.

What is your opinion?

It seems that they have the 7/8 bar size unit, however, a bit pricey I think..