Rear tire #3

[docdoru]

#1: 12,000 miles, 30 psi, wearing the middle
#2: 15,000 miles, 30 psi, with nitrogen, wearing the middle
#3: ? drop to 25 psi, with nirogen opcorn:

 

[Mr.Bumble]

I am having the same problem,I have 30psi in my rear tire and it is wearing in the middle.I hope someone has an answer.:agree:

 

[Firefly]

I am having the same problem,I have 30psi in my rear tire and it is wearing in the middle.I hope someone has an answer.:agree:

Are you thinking you should get more than 15,000 miles out of a rear tire?

The way I like to do burnouts - I'm sure I won't get over 15,000

 

[NancysToy]

I would be thrilled to get 12,000-15,000 out of a rear tire on my BMWs. I am very happy when I make it over 5,000. Those tire cost more, too, and they are more susceptible to road hazards.
-Scotty

 

[Dudley]

The rear tire will be one of my challenges. So far I have 7300 miles and have not touched the middle warning whatchamacallits. It does appear like it is wearing a bit more in the middle. Had been running 30 pounds. After installing the GIVI bags and readjusting the shocks for the extra weight, the rear appeared a bit stiff. I dropped the air to 28 pounds and find it rides a bit smoother. Still kept 20 pounds in the front tires.

 

[Firefly]

In my years of riding it always seems to work out to 1 front tire for every 2 rears.

 

[Sara]

Am I Wrong?-----

--------------but isn't better to have the tire wear down the middle than on either side?????????-----SSSS

 

[SpyderByter]

--------------but isn't better to have the tire wear down the middle than on either side?????????-----SSSS

Sure, better, but idealy, it should wear even. 30 pounds is the max recommended inflation. If it starts wearing in the center only, then you can always drop the pressure down.

A two wheeler will wear the center down first, but this is more like a car tire.

 

[Cundiffla]

I don't know if it makes any different but my book shows the Rear to be 28 psi. I've kept mine right at 28 psi and it seems to be wearing evenly. I am just over 6,000 miles. Would the 2 psi really make that much of difference?

- Larry :spyder:

 

[DragonSpyder]

Always ran mine at 28Lbs and it is almost bald in the middle with half tread on the outsides. I weigh 190Lbs and ride 2up often which brings me to over 300Lbs. I now ride with 21-24Lbs in the rear. It rides much smoother. Getting a new tire this week so will have to see how the wear differs.

 

[tweeder]

If its wearing in the middle then its overinflaited, if it's wearing on the outsides then it's underinflaited.

 

[Firefly]

Just took a closer look at mine - yup - wearing more in the middle than on the sides. Think I'll drop the pressure a bit and see how that works.

 

[SpyderByter]

I don't know if it makes any different but my book shows the Rear to be 28 psi. I've kept mine right at 28 psi and it seems to be wearing evenly. I am just over 6,000 miles. Would the 2 psi really make that much of difference?

- Larry :spyder:

My manual and the one one this site shows a MIN of 26 and MAX of 30.

http://spyder.brp.com/NR/rdonlyres/A86F2B61-B5BE-4BE9-8E75-31BAFBB36FC0/0/OperatorsGuide_2008_en.pdf

Page 79

I just brought mine up to 30. By eye it looks to be wearing more in the middle, even before I pumped it up. It had 28. I have 2000 miles on it. I had no reason to bring it up to 30 except to try it and I already had the compressor out. If I don't like the feel, I figure it will be easy to let out a little at a time till I do.

 

[bjt]

While researching tires in preparation for buying a new rear tire for the Spyder, I read that some wide, low profile tires have a tendency to wear more in the center of the tread than on the edges even when properly inflated.

 

[SpyderByter]

While researching tires in preparation for buying a new rear tire for the Spyder, I read that some wide, low profile tires have a tendency to wear more in the center of the tread than on the edges even when properly inflated.

I have to guess that happens even moreso on the Spyder. Figure on a car, the front tire's edges get some wear from cornering, not so much for the rear tire on a Spyder.

 

[Questions]

My 2-cents worth. I am running a GoldWing 1800 W/Hannigan GTL Side-Hack. Have a Michelin Harmony 205-55-16 on the rear of the Wing. At 28psi i will get 30K + on mileage. Why can't an Auto tire be put on the rear of the Spyder?

Thanks,Slim

 

[NancysToy]

While researching tires in preparation for buying a new rear tire for the Spyder, I read that some wide, low profile tires have a tendency to wear more in the center of the tread than on the edges even when properly inflated.

That was my understanding, too. I have also been told that the rim width vs. tire width has a lot of effect on how the tire wears with a belted tire. Belted tires tend to run quite flat on the road, even at varying pressures.
-Scotty

 

[Dudley]

Here is a question that's been bugging me and may be all stupid and off the wall. For all you car jockies and dragster inthusiasts...when a dragster heats up his tires before a race, the centrifugal force of the tire spinning causes the tire to rise. With the light weight of the Spyder, could it be that, undetectable by the human eye, the tire could be running more in the center because the centrifugal force is doing the same thing in a much smaller scale and causing the center to wear out sooner? Don't laugh too hard!:dontknow:

 

[NancysToy]

Here is a question that's been bugging me and may be all stupid and off the wall. For all you car jockies and dragster inthusiasts...when a dragster heats up his tires before a race, the centrifugal force of the tire spinning causes the tire to rise. With the light weight of the Spyder, could it be that, undetectable by the human eye, the tire could be running more in the center because the centrifugal force is doing the same thing in a much smaller scale and causing the center to wear out sooner? Don't laugh too hard!:dontknow:

Actually, Dudley, that's not so far fetched. The stiffer construction of a regular tire, the thicker tread, and the flatness of the belt are supposed to try to overcome this natural tendency. That's Basic Tire Design 101. Like everything in the world, nothing is perfect, however, and it still could happen to some extent, varying from tire to tire. Fortunately for a car or a Spyder, the tires are smaller diameter, turn at a slower rpm, and a street vehicle is geared lower, so there is less tendency for centrifugal force to distort the tire.
-Scotty

 

[Dudley]

Actually, Dudley, that's not so far fetched. The stiffer construction of a regular tire, the thicker tread, and the flatness of the belt are supposed to try to overcome this natural tendency. That's Basic Tire Design 101. Like everything in the world, nothing is perfect, however, and it still could happen to some extent, varying from tire to tire. Fortunately for a car or a Spyder, the tires are smaller diameter, turn at a slower rpm, and a street vehicle is geared lower, so there is less tendency for centrifugal force to distort the tire.
-Scotty

So the absence of enough weight could cause the tire to have a tendency to be running more on-center than evenly flat? At high speeds the centrifugal force is pretty strong. Do you know what the wheel RPM is at 80 MPH?