Rear Brake Caliper

[remark2013]

I do not have a good relationship with the dealer, they do not and are not willing to give out too much info. My other problem with Spyder Dealers, I'm just over a 100 miles away from the nearest one. I'm going to try one more time tomorrow morning using a tip Joe Meyer gave me. I will report back with the results.

kent

 

[UtahPete]

Harbor freight has the piston tools too. :thumbup:

What is the tool called, do you know?

Also, I saw a thread or post here where someone made their own, but didn't provide dimensions. I probably need to do that because I'd have to make a 90 mile trip to get this tool from Harbor Freight and I'm not going to do that.

Thanks.

 

[UtahPete]

A lot of the automotive parts stores sell a tool to turn in the pistons on automobiles. Someone should measue the distance between the pin holes and measure the hole size. When they have there's apart. And post it here.

Does anyone have those dimensions? I'm probably going to have to make my own. Thanks.

 

[trikermutha]

What is the tool called, do you know?

Also, I saw a thread or post here where someone made their own, but didn't provide dimensions. I probably need to do that because I'd have to make a 90 mile trip to get this tool from Harbor Freight and I'm not going to do that.

Thanks.

https://www.harborfreight.com/disc-brake-pad-and-caliper-service-tool-kit-11-pc-63264.html

Then wait for a super coupon and its even cheaper. Or I use this on my car caliper and worked well.


https://www.harborfreight.com/push-pin-pliers-63700.html

Or there's another version that is square

https://www.lowes.com/pd/KD-Tools-Automotive-Disc-Brake-Piston-Tool/50190675?cm_mmc=SCE_BINGPLA_ONLY-_-ToolsAndHardware-_-SosHandTools-_-50190675:KD_Tools&CAWELAID=&kpid=50190675&CAGPSPN=pla{ifdyn:dyn}&k_clickID=7fc37dde-74bb-47c4-ac56-63008146388c&msclkid=c0fa117b71911453740d4a3b9b64cefd


https://www.homedepot.com/p/Lisle-D...PIPHorizontal2_rr-_-301384006-_-207011085-_-N

 

[Joerolwing]

brembo brake piston turning tool

Originally Posted by Joerolwing
I started with two fender washers with. 3/8" hole, glued them together, clamped them in a mandrel mounted in a drill press, and used a angle grInder to reduce the diameter to 1 3/8". I then squared the center hole to 3/8", then drilled and tapped holes for 1/8" 1/4" long screws, each 3/8" from center on the same line drawn through the center. Next, using a 1 1/2" long 1/2" bolt, I filed the end to a 3/8" square, possibly a fraction oversized. I then cut a 1" wide, 1/8" thick angle bracket from Home Depot and cut it in half at the angle. Next, I drilled and tapped it for the 1/2" bolt. Thread the bolt through this plate then press the bolt end into the washers, making certain the two "pins" are pointing opposite the bolt.

 

[UtahPete]

Originally Posted by Joerolwing
I started with two fender washers with. 3/8" hole, glued them together, clamped them in a mandrel mounted in a drill press, and used a angle grInder to reduce the diameter to 1 3/8". I then squared the center hole to 3/8", then drilled and tapped holes for 1/8" 1/4" long screws, each 3/8" from center on the same line drawn through the center. Next, using a 1 1/2" long 1/2" bolt, I filed the end to a 3/8" square, possibly a fraction oversized. I then cut a 1" wide, 1/8" thick angle bracket from Home Depot and cut it in half at the angle. Next, I drilled and tapped it for the 1/2" bolt. Thread the bolt through this plate then press the bolt end into the washers, making certain the two "pins" are pointing opposite the bolt.

Thanks for reposting this. Do you by chance have a picture of it?

 

[IdahoMtnSpyder]

OK, I am helping a friend change the rear brake pads on his 2014 RT, we have the caliper off the bike and start screwing the piston into the body by turning it clockwise to compress the piston, only the piston just spins it doesn't screw into the body! We turned the piston at least 50 full revolutions so I'm sure something is not right. Any ideas why?:dontknow::dontknow::dontknow:

Thanks, Kent

I had to take the caliper off the bike completely so I could put it into a vise in order to get enough push-in force to get the threads to catch. Read about my warning here: http://www.spyderlovers.com/forums/...ke-pad-change-caution&highlight=brake+caution

I made a tool by taking a flat piece of steel 1" wide and ground and cut a gap in the middle leaving tabs at the two edges. It doesn't take much to turn the piston once it catches the thread. Pushing it in while turning until it does catch is the hard part. I'd post a pic of the tool but I can't find it now! :banghead:

If you do remove the caliper from the brake line you need to bleed the rear caliper after installing and have the dealer eventually do a BUDS bleed process.

 

[Joerolwing]

Thanks for reposting this. Do you by chance have a picture of it?