RT mirror backing removal

[Revalden]

I doesn't. The flasher light is sold as a complete unit only since it's LED. To replace a bulb you are on your own!

Thanks IMR, It's a good thing I waited for this response. How does it come off the mirror? I did get the mirrors apart enough to put in small green arrow lights in the lower corner, it's the only place with enough space for the body of the light. It's just so that I know if the turn signals are still on because the ones in the cluster are hard to see in daylight.

[IdahoMtnSpyder]

How does it come off the mirror?

Three screws from what I see on the parts diagram. Go to http://epc.brp.com/ and look at the exploded view of the mirror in the parts diagram for your Spyder.

[Revalden]

Thanks for that info, I save it to my laptop. But how does the actual mirror glass come off to get at those screws?

[Lew L]

I have the MUTH mirrors and they required removing the glass. Heat gun on lowest setting, carefull prying. I didn't break either one, but I took my time.

[IdahoMtnSpyder]

Thanks for that info, I save it to my laptop. But how does the actual mirror glass come off to get at those screws?

Did you look closely at the diagram? The mirror glass is on one side of the main support, the flasher on the other side. You'll need to take at least the top cover off to get to the screws. I've never done it, just looked at the parts diagram.

[bcer960]

I have the MUTH mirrors and they required removing the glass. Heat gun on lowest setting, carefull prying. I didn't break either one, but I took my time.

I have similar to muth mirrors. I pried them off carefully with a metal ruler, and sprayed pain thinner in between it helps eat the glue. but go slow...

[Revalden]

Why don't you change the reflectors on the rear side of the front fenders to LED's and have them flash with the turn signals. I have them and they are way brighter than anything you are going to put on the mirrors.

Just saying

I might try that if the fenders have the rear lights, I just don't remember ( damn Senior Moments), the ones I just put in the mirrors aren't very bright after all that work getting them in there. I do have some strip LEDs but don't think there are any yellows. I guess reds would work ok.

[upsdoctor]

I hade Muth signals on my 2010 RT and I loved them. I shipped the mirrors to Muth and they installed the LED's for me. https://shop.muthco.com/canam-signal-mirrors

[ThreeWheels]

Hey, not for nothing, but the turn indicator arrows on the 2020 RTL are very visible and don't need any improvement.....................

[zuni]

I followed the instructions that Finless Bob had posted with his video (Including making a template of both pieces just in case). I put the arrows behind the glass on my 2014 RTs. Slow going and lots of work. They look great at night but are not all that visible on a sunny day. I do not plan on repeating with the 2017 RTs I have now.

CJ JAX

[bcer960]

I followed the instructions that Finless Bob had posted with his video (Including making a template of both pieces just in case). I put the arrows behind the glass on my 2014 RTs. Slow going and lots of work. They look great at night but are not all that visible on a sunny day. I do not plan on repeating with the 2017 RTs I have now.

CJ JAX

I followed the same instructions. I've always said they were more for me, to notice the signal is still on, than for other drivers.

[scarecrow]

I'm looking through my old thread bookmarks, at least one person has put the Chevron LED's behind the stock mirrors to have turn signals in the mirror.
Here's the thread I remember, http://www.spyderlovers.com/forums/s...nal-on-mirrors

Did that on my 14rts. Took some time, but they look great. or go to muth mirror systems. They have it for the RT's