Newbie Question - what's the vibration

[Kensouthdakota]

Ok guys since I’m new to Spyder I’m allowing my self 5 rookie questions.
I bought a 2019 Spyder about two weeks ago and it’s been a pleasure to ride, I’ve ridden BMWs for 38 years and the Spyder was a natural transition to three wheels.
We rode a little over 1k this past weekend and I kept noticing a vibration as we pulled small hills, it was not noticeable on the flat roads or at high speeds actually it was sort of a grinding vibration.
I would appreciate any information that you care to share.
I would add that we have a 2014 Spyder also and I’ve never noticed any vibration in it.

 

[oldguyinTX]

Best guess - harmonic vibration from the belt. Belt tension might be wrong. Your 2014 belt tension may be correct. Others on here can give you tips on checking the tension with a Kricket with the rear wheel on the ground and off the ground, and the adjustment procedure. My understanding is that it is not hard, just time consuming as the adjustments have to be made in small increments so as to keep the rear wheel aligned. I do know that the real axle nuts have to be loosened, adjustment made, nuts tightened, ride, repeat. Just my 2 cents worth.

 

[chipveres]

Or you could install a vibration damper ("belt tensioner") if the cycle doesn't already have one.

 

[BajaRon]

I agree with the others. Most likely belt vibration. Different speeds and torque pressure can produce varying occurrence and severity. If it is minor, I would not worry about it. Vibration dampeners can present issues of their own. If you get one. Make sure it is high quality. That little wheel can spin at 30k rpm or even higher. You don't want that coming apart.

The vibration may be annoying, but it will not hurt anything.

 

[Kensouthdakota]

Thanks guys, I was guessing that it might have something to do with the belt.

 

[BLUEKNIGHT911]

Thanks guys, I was guessing that it might have something to do with the belt.

If that Spyder has ONLY been serviced at a Dealer ..... then they may have adjusted the belt tension to BRP specs ...... which many, many folks here think is too high .... I set my 14 RT at 160 lbs. wheels on-the-ground using the KrirKit gauge .... I have no vibes ( which a common cure ) .... good luck ....Mike :thumbup:

 

[sledge]

that would be my guess , because first ever problem with my Spyder was the Drive Belt , I bought a Krikit Guage from BajaRon , and adjusted on it for 4 or 5 times , finally found the spot for me..... 150 lbs. . . not sure if thats good for anyone else , just raise it a little... and check it , if still there go down some and check it . , just what I did and it fixed my problem. good luck

 

[Isopedella]

If you dont have one you may wish to pick up a Krikit. Measures that belt tension.



My belt feels fine but the Tech who did the pulley said it was just a tad low. He did not adjust it.
He used some electronic gizmo with a digital reading.

 

[BajaRon]

If you dont have one you may wish to pick up a Krikit. Measures that belt tension.

View attachment 205055

My belt feels fine but the Tech who did the pulley said it was just a tad low. He did not adjust it.
He used some electronic gizmo with a digital reading.

Those high tech gauges are cool and give a very precise digital readout. Very expensive and usually not very portable. It is amazing that the Krikit II reads within just a few pounds of an electronic, digital gauge. Be careful to get the Krikit II and not the Krikit, which is designed for lighter belts, as it won't read to the weight needed for the Spyder. They look the same but read in different ranges.

Any time I go to an event. Several riders will ask me to check their belt tension. The Krikit II is a great little tool. Easy to use and very accurate if used correctly. To be sure you're doing it right, take 3 readings that all come out the same. Once you get the hang of it, it is very easy to get it right the 1st time.