-
Wet gauges
-
I have never seen that before. But have removed both gauges and use the bar graft.
-
SpyderLovers Sponsor
Bad seals I would say...disconnect both and use on board display more accurate.
Tall flag mount, spyderpops skid plate & stainless steel screen mesh, airhawk adjustable cushion, raised white lettered tires.
-
I haven't seen it either. I'd visit the dealer to see about warranty replacement. If out of warranty, I'd look at using the digital gauges, but someone here who has switched to digital and replaced his/her gauges with something else might be able to make you a deal on their old ones.
-
Not yet..!!
but for sure you can get a good deal from those who have replaced them with other gauges. First check with dealer they should cover them regardless. They should not have condensation on the inside...good luck..
2012 RS sm5 , 998cc V-Twin 106hp DIY brake and park brake Classic Black
-
-
Brought them to my dealer today. He's ordering two new gauges under warranty.
Still, I'd love to replace them with something. Any suggestions
Thanks!
Sent from my iPad using Tapatalk HD
-
Very Active Member
After a week of heavy rains here, accompanied by high humidity, I had some fog on the inside of my gauges.
I went riding on the first sunny day and left the Spyder out in the sun and the fog has gone away.
It hasn't returned.
YET
If it ain't broke, don't break it.
IBA #47122
2020 RT Limited Asphalt Grey
-
Active Member
-
Very Active Member
Originally Posted by Jonnyvermont
Brought them to my dealer today. He's ordering two new gauges under warranty.
Still, I'd love to replace them with something. Any suggestions
Thanks!
Sent from my iPad using Tapatalk HD
I replaced mine with a 12v power socket and a USB power socket.
Dash USB Power 01.jpg
JT
-
Funny, well not funny, but coincidental that this thread was started yesterday. I took my 2013 RT-S to the car wash yesterday just about the time this thread was posted. I did everything known to man kind while spraying my spyder that should have caused the same situation. After reading your post, I went out in the garage and looked at my spyder just to check. Nary a drop or fog on the insides of the guages.
Chris
-
You have many options ... here's ours Lighted Cup Holder on Left & Teddy-Cam on Right
Originally Posted by Jonnyvermont
Still, I'd love to replace them with something. Any suggestions Thanks!
Sent from my iPad using Tapatalk HD
-
Active Member
-
Originally Posted by jthornton
Looks sweet. Could you possibly tell us where you purchased it along with the part #.
Thanks.
-
I wired mine SAE connector direct to battery and ran it up through the hole in the center button area that is used for the CB switch. Removed plastic cover ( snaps off) there is a round hole. Used the plastic wire fishing tool I got with my glow rider installation. Removed left panel on my 2013rt , inserted tool through hole until I could see it on left side , pulled SAE wire up through hole. Went to auto store found a round grommet that looks like a miniature construction cone . Pulled grommet over SAE connector and installed in hole. The SAE wire I used , came with my battery tender junior , I brought an extension and a USB connector(about 2in long) from same manufacture of my battery tender.
I use this to connect battery tender jr. Or I can use the cigar lighter connector ( comes with tender or USB connector ( sold separately $ to power anything.
Did not have to cut anything and I can remove if I swell or trade in. Hopes this info helps you !
-
Active Member
Oh, that's a good idea! I like the idea of using an SAE connector. So the white flange around the USB port... did you make that or did it come with the battery tender? I guess I'm trying to figure out how you got the charger to sit cleanly and securely in the gauge hole.
Oh: I just reread... you said that's the grommet that looks like a miniature construction cone!! (Need more coffee) I'll have to see if I can find what that might be. I don't think I've ever seen such an animal there, but haven't been looking.
Last edited by dsvogel; 11-15-2013 at 08:57 AM.
-
One correction to the above install! The cigar connection came with my slim air compressor , uses SAE connector also .
-
The white ring you are referring to is for a grill instal , mine was installed through center button on dash .
-
It was't in the area in the store where you normaly find grommets . It was where the have some kind of sensors, and the grommet was in that area. Good luck (:
-
Very Active Member
Originally Posted by AZLife
Looks sweet. Could you possibly tell us where you purchased it along with the part #.
Thanks.
The Dual USB is a Blue Seas PN 1016, the adapter I made in my machine shop and powder coated black.
Here is what it looks like after I powder coated the adapter.
Dual USB Installed.jpg
JT
Last edited by jthornton; 11-16-2013 at 07:50 AM.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|