-
Active Member
Front sprocket access
Has anyone figured out a way to make the small black cover that blocks getting at the front sprocket on an RT easier to remove?It really isn't held on by much at all but to get it off you need to pull several other panels off.If it was easier then checking the sprocket and belt or tensioner would be so easy.Maybe some dzus fasteners or quick release setup.
:
: 2017 RTL ORBITAL BLUE
-
Very Active Member
Originally Posted by spyder01
Has anyone figured out a way to make the small black cover that blocks getting at the front sprocket on an RT easier to remove?It really isn't held on by much at all but to get it off you need to pull several other panels off.If it was easier then checking the sprocket and belt or tensioner would be so easy.Maybe some dzus fasteners or quick release setup.
Why, simpler to accomplish without modifications some preventative maintenance. Gain access, remove the pulley, inspect, reuse if serviceable, install onto wetted splines and reassemble.
Simply not worth risking possible damage to the countershaft itself.
-
Active Member
Why,because I like to keep a close eye on that rear drive area.Ive been off road a fair amount and Ive gotten mud in there plus I have a tensioner which I want to inspect the roller from time to time.This area seems to be one that gets talked about a lot on this forum so if I could remove this cover a little easier that would help.Plus I dont like to leave things alone,Ive had a good time fiddling around with my Spyder.
:
: 2017 RTL ORBITAL BLUE
-
Very Active Member
Quick question here about front sprocket inspection. I've read all the inspection threads, I'm comfortable with that. How about re-installation? Talking the new upgraded torque value of 111 FT/Lbs ±4. How do you lock the shaft from turning? Do you let the belt take the stress and the parking brake keep the shaft from turning? Is there a pulley locking tool? I haven't seen much mention of this specific thing, any help would be appreciated.
h0gr1der
2018 RT Limited Blue/Chrome SE6 *Tri-Axis Bars*Adjustable Driver Backrest*175/55R15 Vredestein Front, 205/60R15 Vredestein Rear Tires*Baja Ron Front Spring Pre-Load Adjusters*Misty Mountain Sheepskin seat cover*Centramatic balancers *Garmin Zumo 595LM GPS*KOTT Grills*BajaRon swaybar*SpyderPops Alignment*Missing Belt guard*Magnetic Mirrors*Custom Rear Adjustable Shock*360° LED Headlights & Foglights*Progressive front fender turn signals
States Visited on Less than 4 wheels.
-
Very Active Member
Originally Posted by spyder01
Why,because I like to keep a close eye on that rear drive area.Ive been off road a fair amount and Ive gotten mud in there plus I have a tensioner which I want to inspect the roller from time to time.This area seems to be one that gets talked about a lot on this forum so if I could remove this cover a little easier that would help.Plus I dont like to leave things alone,Ive had a good time fiddling around with my Spyder.
Access for removing mud or debris, or inspecting a tensioner is understandable.
Pretty easy mod. Leave enough edge and trim out the inspection cover size you prefer. Install a doubler flange behind your cutout perimeter. Secure that and fasten the access cover last.
-
Originally Posted by h0gr1der
Quick question here about front sprocket inspection. I've read all the inspection threads, I'm comfortable with that. How about re-installation? Talking the new upgraded torque value of 111 FT/Lbs ±4. How do you lock the shaft from turning? Do you let the belt take the stress and the parking brake keep the shaft from turning? Is there a pulley locking tool? I haven't seen much mention of this specific thing, any help would be appreciated.
I have changed out several sprockets. Once you get the belt back on, and the rear shock re-mounted, I slid a broom handle through the rear wheel and let it clamp to the frame when torquing the front bolt. Also, look up the new paste to put on the splines. It transfers torque better, but I forget what it is called. I bought a tiny little tube of it. There has been a lot of questions on keeping the spline dry, using high temp grease, etc. but BRP finally put out a bulletin said to use gear grease. Maybe someone here can remember what it is called.
-
Very Active Member
Originally Posted by stevencovert
I have changed out several sprockets. Once you get the belt back on, and the rear shock re-mounted, I slid a broom handle through the rear wheel and let it clamp to the frame when torquing the front bolt. Also, look up the new paste to put on the splines. It transfers torque better, but I forget what it is called. I bought a tiny little tube of it. There has been a lot of questions on keeping the spline dry, using high temp grease, etc. but BRP finally put out a bulletin said to use gear grease. Maybe someone here can remember what it is called.
The info I saw called out a specific Kluberpaste. Forgot the exact number but researched it. Seemed pretty basic in regards to performance.
-
Very Active Member
h0gr1der - to answer your question, I applied the park brake, chocked the rear wheel and torqued the bolt to 110ft lb. I put Molykote paste on the splines, taking particular care to keep it from transferring to the inner & outer pulley faces upon installation. That was about 8 years ago and all good since. Just do it!
The best substitute for brains & knowledge is....................silence.
-
Very Active Member
Is there an upgraded pulley available?
2015 RTS SE6 Special Series Red/Black w/Magnesium front fenders(bought in Nov. 2018 w/9,400 miles)
Dynojet Power Commander V, Power Commander POD-300 Display, PCV Map Switch, Pedal Commander (WOW)
Passenger Arm Rests, Windshield Air Wing
Baja Ron's Sway Bar & Spring Adjusters
Air Scoops, LaMonster's Hiway Pegs
Magnetic Mirror Mounts, Air Innovations Seat Cushion
Red Chrome pin striping on Black hood
Federal Formoza AZ01 front tires (they're GREAT)
Kumho Ecsta AST KU25 All-Season Tire - 225/50R15 91H
LED bars above radiator inlets
LED brake/running/turn signals on license plate frame
Tag-Along trailer
LED headlights LED fog lights (WOW)
2" x 2" Road Lights inside front fenders
7' x 10' Cargo trailer
Garmin 396 LM GPS
RLS Cat-delete resonator with China Akropovic muffler
New Banshee AGM
M3 TPMS on front tires
Remote Control for Heated Jacket and Heated Riding Pants
Analog Clock and Analog Volt Meter
Loose Nut Behind Handlebars
-
Very Active Member
Originally Posted by Revalden
Is there an upgraded pulley available?
Not that I am aware of, but there is an upgraded pulley bolt and torque spec depending on the year of your Spyder. The new bolt has a large flange with no washer and torque is up to 111 Ft/Lb ±4 Ft/Lb. Not sure what year they switched.
h0gr1der
2018 RT Limited Blue/Chrome SE6 *Tri-Axis Bars*Adjustable Driver Backrest*175/55R15 Vredestein Front, 205/60R15 Vredestein Rear Tires*Baja Ron Front Spring Pre-Load Adjusters*Misty Mountain Sheepskin seat cover*Centramatic balancers *Garmin Zumo 595LM GPS*KOTT Grills*BajaRon swaybar*SpyderPops Alignment*Missing Belt guard*Magnetic Mirrors*Custom Rear Adjustable Shock*360° LED Headlights & Foglights*Progressive front fender turn signals
States Visited on Less than 4 wheels.
-
Very Active Member
Is a puller required to remove the front pulley, or will it slide of the shaft?
Ours is a red, black and chrome 2017 F3 Limited. Bought new in 2/2019. The avatar is my first bike back in 1952, a Simplex Servi-Cycle. Photo taken at the Barber Museum.
-
Originally Posted by RICZ
Is a puller required to remove the front pulley, or will it slide of the shaft?
Good question. If the pulley is in good condition it's a nice slide fit, if it's rust red you may find it very tight to remove. The red one I did, nothing would made it move, big levers, puller etc. As soon as I lubed it with solvent down the splines it simply slipped off. Magic. Very weird.
-
Very Active Member
Originally Posted by PinkRosePetal
Good question. If the pulley is in good condition it's a nice slide fit, if it's rust red you may find it very tight to remove. The red one I did, nothing would made it move, big levers, puller etc. As soon as I lubed it with solvent down the splines it simply slipped off. Magic. Very weird.
So, would there be an advantage to lubing the splines on a low mileage bike, in the name of preventative maintenance? The bike is a 2017 F3L purchased new last February and has just over 700 miles.
Or should I just not worry about it for a while?
Ours is a red, black and chrome 2017 F3 Limited. Bought new in 2/2019. The avatar is my first bike back in 1952, a Simplex Servi-Cycle. Photo taken at the Barber Museum.
-
Originally Posted by RICZ
So, would there be an advantage to lubing the splines on a low mileage bike, in the name of preventative maintenance? The bike is a 2017 F3L purchased new last February and has just over 700 miles.
Or should I just not worry about it for a while?
I think that would be a reasonable plan. Before I knew about the rust problem I removed my pulley and modified it to get better belt alignment then reassembled it using CV grease. (For info that's grease designed for car constant velocity joints which are extremely highly loaded.) I tightened the bolt to about 120lb/ft. The bike is now at 12k miles and I've rechecked the bolt and sprocket recently and all is ok. The benefit of the preventative maintenance is that there is no degradation of the splines and drive surfaces. If you wait until there is a problem, the part will forever be substandard.
The red one I dealt with wasn't my bike, there is a thread about it if you search, I tightened that one to 110lb/ft, it's done about 6k miles since and it appears to be ok and shows no sign of failing.
At 120lb/ft I felt a little yield so it's possibly a tad too high a torque so I don't recommend that.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|