|
-
 Will this trailer work with a Spyder?
Does anyone use this sort of trailer for their Spyder? I think it would probably work except for the ground clearance of the Spyder and I wonder if there is any scraping when breaking over the bed and the ramp? This one is pretty generic and some shop around must be done prior to purchase.
http://www.tractorsupply.com/tsc/pro...r?cm_vc=-10005
Thanks.
-
Very Active Member
Not wide enough, it has to be at least 6 ft wide. A 6x10 would be a better size. The 5 1/2 x 10 they show would leave you about 3 1/2 inches on each side of the front tires. As far as the ramp, a few well placed boards would do the trick.
http://can-am.brp.com/content/dam/ca...heet%20EN_.pdf
Last edited by Highwayman2013; 12-01-2016 at 11:52 AM.
2016 F3 Limited
2019 Ryker Rally
2014 Suzuki V Strom 650
2020 CSC TT 250
-
Very Active Member
Measure from the outside of the fenders and add a few inches for maneuvering and you will find that 5' is not wide enough.
2011 RTS (Sold to a very nice lady)
1998 Honda Valkyrie
2006 Mustang GT. Varooooom!
US Navy Veteran
SC Law Enforcement Boat Captain
CNC Machine Service Technician
President: Rolling Thunder SC1
Member: Disabled American Veterans, Rock Hill, SC
Member: American Legion
Experience is recognizing the same mistake every time you make it!  
-
Very Active Member
 Originally Posted by Highwayman2013
Not wide enough, it has to be at least 6 ft wide. A 6x10 would be a better size. The 5 1/2 x 10 they show would leave you about 3 1/2 inches on each side of the front tires. As far as the ramp, a few well placed boards would do the trick.
http://can-am.brp.com/content/dam/ca...heet%20EN_.pdf
Originally Posted by Grandpot
Measure from the outside of the fenders and add a few inches for maneuvering and you will find that 5' is not wide enough.
Cruzr Joe
2018 F3 Limited, BRP Driver Backrest, Spyderpops Lighted Bump Skid, Dual Spyclops Light, Mirror Turn Signals, Laser Alignment, Engine LEDs, Fog Lights With Halo's, Cushion Handgrips, BRT LEDs, and Under Lighting, Lamonster IPS, (with Clock), F4 25" Vented Windshield with Wings, Airhawk "R" Cushions. Position 4 Brake setting, Short reach Handlebars, Dash Mounted Voltmeter and 12 Volt Plug. Set of 3rd pegs. Extended Passenger Seat. Exterior BRP Connect setup, Ultimate Trailer
-
Re
IMG_0106.jpg
IMG_0104.jpg
11/2" clearance on each side and fabricate extensions for the ramp so it will latch approx 20 degrees back lean and fits just fine. I also installed a wood deck on it.
PM me for more info
F-3 will fit on a 5x8
I think the other models are wider and won't fit
Last edited by Gsebring; 12-01-2016 at 03:41 PM.
-
Very Active Member
MEASUREMENTS !!!!!!!
Originally Posted by Habib
Does anyone use this sort of trailer for their Spyder? I think it would probably work except for the ground clearance of the Spyder and I wonder if there is any scraping when breaking over the bed and the ramp? This one is pretty generic and some shop around must be done prior to purchase.
http://www.tractorsupply.com/tsc/pro...r?cm_vc=-10005
Thanks.
If you look closely at the measurements - the 5 ft ( 60 inches ) is outside the frame, so it's really 57 in. inside ....no way Jose' ....... Like others said get a 6 X 10 minimum it can't be much more - try Home Depot - Lowe's ........jmho ......Mike 
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
Reply With Quote