-
2015 RT Limited Reverse
2 times my RT Limited will not go into reverse, anyone have any Ideas?
-
you sure you have your foot completely on the brake?
only happened to me twice and figured out pretty fast I didn't have enough pressure on the brake pedal. never have had an issue since.
-
Very Active Member
Originally Posted by tmarsanto
2 times my RT Limited will not go into reverse, anyone have any Ideas?
Be sure that your Spyder is
1) Motor is Running
2) Stopped
3) Foot firmly on brake
4) Push and hold top round button while you pull the paddle shifter towards you.
If you are following these steps and it still wont go into reverse
1) check your oil level
2) take it to your dealer
Cruzr Joe
2018 F3 Limited, BRP Driver Backrest, Spyderpops Lighted Bump Skid, Dual Spyclops Light, Mirror Turn Signals, Laser Alignment, Engine LEDs, Fog Lights With Halo's, Cushion Handgrips, BRT LEDs, and Under Lighting, Lamonster IPS, (with Clock), F4 25" Vented Windshield with Wings, Airhawk "R" Cushions. Position 4 Brake setting, Short reach Handlebars, Dash Mounted Voltmeter and 12 Volt Plug. Set of 3rd pegs. Extended Passenger Seat. Exterior BRP Connect setup, Ultimate Trailer
-
Very Active Member
Originally Posted by tmarsanto
2 times my RT Limited will not go into reverse, anyone have any Ideas?
If the bike is still moving when you hit the shift paddle, and you did that before you got the brake pressed, it won't shift. You then have to let off both the shift paddle and brake and start the sequence over.
2014 Copper RTS
Tri-Axis bars, CB, BajaRon sway bar & shock adjusters, SpyderPop's Bumpskid, NBV peg brackets, LED headlights and modulator, Wolo trumpet air horns, trailer hitch, custom trailer harness, high mount turn signals, Custom Dynamics brake light, LED turn signal lights on mirrors, LED strip light for a dash light, garage door opener, LED lights in frunk, trunk, and saddlebags, RAM mounts and cradles for tablet (for GPS) and phone (for music), and Smooth Spyder belt tensioner.
-
Very Active Member
Originally Posted by Cruzr Joe
Be sure that your Spyder is
1) Motor is Running
2) Stopped
3) Foot firmly on brake
4) Push and hold top round button while you pull the paddle shifter towards you.
If you are stopped you do not have to press the brake in order to shift into reverse. But you do have to press the brake to shift into 1st. At least that's the way it works with my 2014 RTS.
2014 Copper RTS
Tri-Axis bars, CB, BajaRon sway bar & shock adjusters, SpyderPop's Bumpskid, NBV peg brackets, LED headlights and modulator, Wolo trumpet air horns, trailer hitch, custom trailer harness, high mount turn signals, Custom Dynamics brake light, LED turn signal lights on mirrors, LED strip light for a dash light, garage door opener, LED lights in frunk, trunk, and saddlebags, RAM mounts and cradles for tablet (for GPS) and phone (for music), and Smooth Spyder belt tensioner.
-
I will make sure of it tomorrow and see what happens.
Originally Posted by DJFaninTN
you sure you have your foot completely on the brake?
only happened to me twice and figured out pretty fast I didn't have enough pressure on the brake pedal. never have had an issue since.
-
Originally Posted by Cruzr Joe
Be sure that your Spyder is
1) Motor is Running
2) Stopped
3) Foot firmly on brake
4) Push and hold top round button while you pull the paddle shifter towards you.
If you are following these steps and it still wont go into reverse
1) check your oil level
2) take it to your dealer
Cruzr Joe
Ok thanks
-
If your RPM is too high it will not go in reverse.
Sent from my iPad using Tapatalk
-
When I have trouble getting mine ready to back-up: it's normally because I'm not getting the "R" button and backshift paddle on the same page of the game plan...
Just make sure that you're stopped, and you've got your foot on the brake. (Who wants to try and shift without doing this?????)
FIRMLY press and hold down "R"
Then hit the backshift paddle!
If you hit "R" and backshift at the same time: you ain't going anywhere!
-
Very Active Member
Originally Posted by Bob Denman
When I have trouble getting mine ready to back-up: it's normally because I'm not getting the "R" button and backshift paddle on the same page of the game plan...
Just make sure that you're stopped, and you've got your foot on the brake. (Who wants to try and shift without doing this?????)
FIRMLY press and hold down "R"
Then hit the backshift paddle!
If you hit "R" and backshift at the same time: you ain't going anywhere!
My 2013 does this on occasion, and as Bob said, foot on brake, press "R" button, then hit paddle shifter. This has worked for me.
"A Wise Man Once Said, I Should Ask My Wife."
2017 Champagne Metallic RT-S SE-6 Rivco Dual Flag Holders; Slingmods Highway Pegs; (Hate Them) Airhawk Seat Cushion; Show Chrome Black Touring Rack w/ Risers & Touring Windshield; RAM X Mount For TXTAG; TackForm Phone Mount; Lidlox; Magic Mirror Mounts; Guardian Bells; WOLO "Bad Boy" Air Horn; Dual USB Power Outlet With Voltmeter; 12V outlet for misc. stuff; Spyderpops Full View Mirror Turn Signals; Large Brake Pedal; Kott Grilles; Large Mud Flap; BajaRon 3 Piece Sway Bar, Last But Not Least, Kuhmo Rear Rire, Vedrestien Fronts.
2017 RT-S , Brake pedal extender is twice the size of the stock pedal. Champagne Metallic
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|