-
Installing the Baja Ron Sway Bar on a 2015 RT
Hi, I'm the new owner of a 2015 RT Limited.
I've been reading about the Baja Ron Sway Bar and the ROLO system laser alignment and that they can improve the ride and handling of the bikes.
Is the Baja Ron Sway Bar something an average DYI guy can install and are there any special tools needed?
-
Easy to do as long as you have the means to get the front end about 2 feet off the ground to get the old bar out and the new one in.....
-
Very Active Member
Yes, the hardest part is getting the front of the spyder high enough to get the old bar out and the new bar in. 22 inches is recommended, but that is only remove and install the bar, everything else can be done with drive on ramps about 10 inches high. The bar will come with great instructions, just read and understand them before you start.
David
How old would you be if you didn't know how old you were?
-
Not bad at all to change out. I used two motorcycle/atv lifts. One under each front tire. Took me about an hour and fifteen minutes start to finish. Take your time and work safely.
-
Sway Bar install
I just installed Rons sway bar on my 2015 RTL today. His directions are fantastic. I used car ramps with two inch blocks under ramp. Used a floor jack to go up high enough to get the old bar out and the new bar in. Lowered it back on the ramps and finished the job. Wasn't to hard at all!!
-
Yes...
Diy'fers can do this with the instructions provided...you need to be those that read instructions. . but as mentioned above the height is the tough part...
2012 RS sm5 , 998cc V-Twin 106hp DIY brake and park brake Classic Black
-
What is the advantage of putting the new sway bar on a 2015 RT? I have seen it come up again and again, but my bike seems to handle fine to me. It may be me still getting use to the difference from 2 wheels to 3.
-
Originally Posted by Big Will 51
What is the advantage of putting the new sway bar on a 2015 RT? I have seen it come up again and again, but my bike seems to handle fine to me. It may be me still getting use to the difference from 2 wheels to 3.
I thought the same thing! You can't explain the difference, but, it is AMAZING!! The ryde is nice before you get it, and incredible with the new sway bar. Just added one on my 15 RT limited last week!
-
Originally Posted by DanT
Hi, I'm the new owner of a 2015 RT Limited.
I've been reading about the Baja Ron Sway Bar and the ROLO system laser alignment and that they can improve the ride and handling of the bikes.
Is the Baja Ron Sway Bar something an average DYI guy can install and are there any special tools needed?
Took mine to the dealer...1/2 hour and we were out the door!
Saved the hubs from trying to balance my bike on some contraption and my nerves helping him!!
-
Very Active Member
Originally Posted by Charlotte17078
I thought the same thing! You can't explain the difference, but, it is AMAZING!! The ryde is nice before you get it, and incredible with the new sway bar. Just added one on my 15 RT limited last week!
I get a lot of calls asking me to explain exactly what the sway bar does for the Spyder. And you're right. I can give you all kinds of technical data of exactly what the bar does. But all of that doesn't get the true effect across. But as soon as people get a chance to ride the bar. Their eyes light up and they go 'AH! Now I understand!
It's so much fun to see that look of comprehension.
Thanks everyone! You all do a better job of explaining my bar kit than I ever could! Enjoy the ride!
Only SLOW people have to leave on time...
<a href='https://www.spyderlovers.com/adserver/www/delivery/ck.php?zoneid=13' target='_blank'><img src='https://www.spyderlovers.com/adserver/www/delivery/avw.php?zoneid=13&cb=7845674567' border='0' alt='' /></a>
-
Spot me on an IBA ride
Last edited by CMA/IBA_rider; 04-22-2016 at 04:42 PM.
-
Someone told me that the 2016 RT has a larger Sway Bar than the 2015's...... Is that true?........
-
Very Active Member
Originally Posted by vstrommer
Someone told me that the 2016 RT has a larger Sway Bar than the 2015's...... Is that true?.... ....
Sorry, not true. Same bar.
Only SLOW people have to leave on time...
<a href='https://www.spyderlovers.com/adserver/www/delivery/ck.php?zoneid=13' target='_blank'><img src='https://www.spyderlovers.com/adserver/www/delivery/avw.php?zoneid=13&cb=7845674567' border='0' alt='' /></a>
-
Originally Posted by BajaRon
I get a lot of calls asking me to explain exactly what the sway bar does for the Spyder. And you're right. I can give you all kinds of technical data of exactly what the bar does. But all of that doesn't get the true effect across. But as soon as people get a chance to ride the bar. Their eyes light up and they go 'AH! Now I understand!
It's so much fun to see that look of comprehension.
Thanks everyone! You all do a better job of explaining my bar kit than I ever could! Enjoy the ride!
I rode last season completely OEM. I installed Ron's sway bar in early March and the shock adjusters three weeks ago. Made my RTL a completely different ride for the better. It handles the the curves like I'm on two wheels. Makes a big difference in the wind. The shock adjusters have got front end off the ground, which is really nice when I am running the old county roads. The shock adjusters have also cut down on thpe brake dive. I can not even think of going back to OEM.
-
Baja Ron's instructions are great. Easy install and while you have the RT off the ground, install a bumpskid from Spyderpops.
-
About lifting the front end, my driveway has about 18" wide drain. Position bike over drain and it made it easy to install sway bar.
-
Very Active Member
Only SLOW people have to leave on time...
<a href='https://www.spyderlovers.com/adserver/www/delivery/ck.php?zoneid=13' target='_blank'><img src='https://www.spyderlovers.com/adserver/www/delivery/avw.php?zoneid=13&cb=7845674567' border='0' alt='' /></a>
-
Remember the old pits in some garages. Had one in our first house and that gave me the idea.
-
Very Active Member
Is the bar pronounced BA JA OR BA HA Just wondering.
-
Very Active Member
Originally Posted by JP58
Is the bar pronounced BA JA OR BA HA Just wondering.
It is pronounced BaHa. But spelled BaJa. That is because Baja is Spanish. And in Spanish the 'J' carries the English 'H' sound. I'm sure that clears it all up for everyone!
Only SLOW people have to leave on time...
<a href='https://www.spyderlovers.com/adserver/www/delivery/ck.php?zoneid=13' target='_blank'><img src='https://www.spyderlovers.com/adserver/www/delivery/avw.php?zoneid=13&cb=7845674567' border='0' alt='' /></a>
-
-
SpyderLovers Sponsor
-
-
Very Active Member
Only SLOW people have to leave on time...
<a href='https://www.spyderlovers.com/adserver/www/delivery/ck.php?zoneid=13' target='_blank'><img src='https://www.spyderlovers.com/adserver/www/delivery/avw.php?zoneid=13&cb=7845674567' border='0' alt='' /></a>
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|