I have been trying to figure out the best way to place the 6 x 24 (guessing on the dimensions) PGR banner across the windshield on my RT.
I finally decided to make inquiry to the experts here, I know that there are other PGR members here, and perhaps I could profit from your experience.
Thank you in advance,
Joe
U.S. Army Viet Nam Era Vet
2013 Spyder RT-L, Black Currant
Trunk mount dual SS flag holder
TricLed foam hand grips (awesome)
Chromed Soaring Eagle License Holder
Utopia Deluxe driver backrest
LED fender lighting
Fast Flash LED brake light
Spyder Pops LED/skid plate
I rode with the PG for about a year until my back couldn't do the standing. I placed the banner across the outside of the windshield with the bottom edges tucked under the chrome window trim. there is just enough room. Then on the side edges I used those clamp type office document holders (two each side). finally i used two very tiny bungie cords stretched across behind the windshield connecting the holes in the banner. I hope this helps.
2015 an Am Spyder RT Limited
2013 Yamaha WR250R - Sold
2011 Can Am Spyder RT-S SE5 Limited - Sold
2011 Aspen Sentry Trailer
2003 BMW K1200LT - Sold
2007 Unigo Trailer - Sold
2001 BMW K1200LT - Sold
2001 Honda 750 NightHawk - sold
2015 RT Ltd , Canamspyderaccessories Brake pedal ext. Red
I rode with the PG for about a year until my back couldn't do the standing. I placed the banner across the outside of the windshield with the bottom edges tucked under the chrome window trim. there is just enough room. Then on the side edges I used those clamp type office document holders (two each side). finally i used two very tiny bungie cords stretched across behind the windshield connecting the holes in the banner. I hope this helps.
I do the same exact thing, those clips he mentioned are binder clips, I got mine in silver and they don't show as much. If you try and go over the windshield brackets it creeps up and pops loose, I also lower the windshield a little so no vision obstruction. I also have the Rivco flag holders that bolt to the trunk and hold the 6"x9" flags.
Greetings from Idaho
2014 RT-S,
Barjaron swaybar, chome luggage rack, Ram Mount GPS, 12 volt dash outlet, spyderflap mudflap, Rivco flag mounts, drink2go and custom handlebar drink holders,Driver Backrest,Tri-Axis Handlebars, TRICLed turn signal lights. Custon Dynamic Magic Strobe Brake Modulator, Triple Dash Pouches, "Squared Away" Laser Alignment, Spyderpops Bumpskid, TricLed "Knightrider" LED
I have seen many bikes spyder or not using the above mentioned binder clips allows for EZ adjustment pre & post escort, most do not use at highway speeds fyi, some also use small bungee cords & the clips (double secure) I chose the decal as I look right over my windshield anyway. Works for me. SmoothSpyder backrest holds my 8x12flag just great. Talk with your ride captin see if they may hay a temp one you can test out, or point you to another member can show you directly.
Last edited by Bfromla; 05-22-2016 at 02:23 AM.
Reason: Typo
2013 STL SE5 BLACK CURRANT
SpyderPop's: LED bumpskid
SmoothSpyder: dualmode back rest
T r * * LED:foam grip covers, Tricrings, FenderZ,
brake light strips, wide vue mirrors
Rivico SOMA modulation brake leds
sawblade mowhalk fender accents
minispyder dash toy
Lid lox
KradelLock
Pakitrack
GENSSI ELITE LED H4 headlights
FLO (Frunk Lid Organizer)
BRP fog lights, trailer hitch
SENA 20S EVO
2015 an Am Spyder RT Limited
2013 Yamaha WR250R - Sold
2011 Can Am Spyder RT-S SE5 Limited - Sold
2011 Aspen Sentry Trailer
2003 BMW K1200LT - Sold
2007 Unigo Trailer - Sold
2001 BMW K1200LT - Sold
2001 Honda 750 NightHawk - sold
2015 RT Ltd , Canamspyderaccessories Brake pedal ext. Red
I just use the small bungies. I did go through shopping a number of them to get one small enough to
provide enough tension to not "lose it". Mine stays in place easily at Highway speeds(70-80).
Decided to put it across the top of the frunk with and placed a 6" strip of Velcro underneath on booth sides and on the banner, had it up to 73 mph without any problems. Never could find a good way to put on the windshield especially with my camera mounted behind the windshield.
I do the same exact thing, those clips he mentioned are binder clips, I got mine in silver and they don't show as much. If you try and go over the windshield brackets it creeps up and pops loose, I also lower the windshield a little so no vision obstruction. I also have the Rivco flag holders that bolt to the trunk and hold the 6"x9" flags.
I Have a 2015 RT. I'm looking for flag mounts for my trunk. I do not have bolt holes.
any idea?