Results 1 to 8 of 8
  1. #1
    Very Active Member
    Join Date
    Oct 2007
    Posts
    4,672
    Spyder Garage
    0

    Default Frunk weatherstrip

    Wondering if anybody has good ideas for replacing the frunk weatherstrip. Spyderpops seems a little expensive, but not hugely so. JUst wondering if there are other options. It's a 2010 RS-S.

  2. #2
    Very Active Member Cruzr Joe's Avatar
    Join Date
    Jul 2012
    Location
    Bryant, Arkansas
    Posts
    10,146
    Spyder Garage
    0

    Default

    Spyderpops replacement is a little better quality than the OEM, i replaced mine and am very happy.


    Cruzr Joe
    2018 F3 Limited, BRP Driver Backrest, Spyderpops Lighted Bump Skid, Dual Spyclops Light, Mirror Turn Signals, Laser Alignment, Engine LEDs, Fog Lights With Halo's, Cushion Handgrips, BRT LEDs, and Under Lighting, Lamonster IPS, (with Clock), F4 25" Vented Windshield with Wings, Airhawk "R" Cushions. Position 4 Brake setting, Short reach Handlebars, Dash Mounted Voltmeter and 12 Volt Plug. Set of 3rd pegs. Extended Passenger Seat. Exterior BRP Connect setup, Ultimate Trailer

  3. #3
    SpyderLovers Sponsor cptjam's Avatar
    Join Date
    Jul 2010
    Location
    Las Vegas, NV
    Posts
    3,850
    Spyder Garage
    0

    Default Pops

    It works. The OEM poor quality. We put one on the 622. Dry as a bone! Joe
    Joe Meyer



    Dealer for the Outlaw/ROLO laser Alignment system

  4. #4
    Very Active Member PistonBlown's Avatar
    Join Date
    Jan 2013
    Location
    Christchurch, New Zealand
    Posts
    1,123
    Spyder Garage
    0

    Default

    It's effectively the same a car trunk seal so if you have a specialist rubber supplier there you could possibly find an alternative to the EOM stuff, however I'm not sure if it would be cheaper than Spyderpops. Over here it's NZ$18.99 a metre so would work out more expensive. Personally I think all Spyderpops stuff is very reasonably priced.
    Last edited by PistonBlown; 05-11-2016 at 04:02 AM.

  5. #5
    Very Active Member oldguyinTX's Avatar
    Join Date
    Nov 2013
    Location
    Central Texas
    Posts
    3,384
    Spyder Garage
    1

    Default

    Quote Originally Posted by Cruzr Joe View Post
    Spyderpops replacement is a little better quality than the OEM, i replaced mine and am very happy.


    Cruzr Joe
    Took about 5 minutes to install, and was a perfect fit.
    "A Wise Man Once Said, I Should Ask My Wife."
    2017 Champagne Metallic RT-S SE-6 Rivco Dual Flag Holders; Slingmods Highway Pegs; (Hate Them) Airhawk Seat Cushion; Show Chrome Black Touring Rack w/ Risers & Touring Windshield; RAM X Mount For TXTAG; TackForm Phone Mount; Lidlox; Magic Mirror Mounts; Guardian Bells; WOLO "Bad Boy" Air Horn; Dual USB Power Outlet With Voltmeter; 12V outlet for misc. stuff; Spyderpops Full View Mirror Turn Signals; Large Brake Pedal; Kott Grilles; Large Mud Flap; BajaRon 3 Piece Sway Bar, Last But Not Least, Kuhmo Rear Rire, Vedrestien Fronts.
    2017 RT-S , Brake pedal extender is twice the size of the stock pedal. Champagne Metallic

  6. #6
    Very Active Member
    Join Date
    Oct 2007
    Posts
    4,672
    Spyder Garage
    0

    Default

    Spyderpops it is then. Thanks all!

  7. #7
    Very Active Member AMTJIM's Avatar
    Join Date
    Jun 2008
    Location
    Vail, AZ
    Posts
    1,558
    Spyder Garage
    1

    Default

    Most rubber stripping and seals is out sourced, it's probably available by the foot, even on ebay.
    In the twisties I was playing the tart...
    2009 GS SM5 , Red/Black

  8. #8
    Very Active Member
    Join Date
    Oct 2007
    Posts
    4,672
    Spyder Garage
    0

    Default

    It was good advice. Easy swap and great fit. Thanks!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •