New fault code C0042

[DonCopenha]

I just replaced front brake pads, rotors, and rear tire. Now the 2013 RT Limited throws Brake Faults on display. Tried the display reader trick and received a C0042 code which isn't anywhere I can find. Anyone know what's going on? I had a stuck caliper that started all this and now my pedal is softer than it's ever been. Not sure I like the long travel.

[cuznjohn]

are you sure that is the code you got, i could not find it either

[DonCopenha]

I just took it out again and verified. Sort of random events cause it but definitely I get BRAKE FAILURE message and then the console can be used to display C0042.

[Highwayman2013]

Did you bleed the brakes?

[DonCopenha]

Did you bleed the brakes?

Bled the brakes, front and rear, no bubbles. Saw in shop manual something about VMC (VCM) bleeding? Know anything about that?

[trikermutha]

[Azmi93]

I just replaced front brake pads, rotors, and rear tire. Now the 2013 RT Limited throws Brake Faults on display. Tried the display reader trick and received a C0042 code which isn't anywhere I can find. Anyone know what's going on? I had a stuck caliper that started all this and now my pedal is softer than it's ever been. Not sure I like the long travel.

Did you find solution for this problem ? I had the same thing and didnt know what to do
20200915_190109.jpg

[ARtraveler]

This thread goes back to 2015.

[Fatcycledaddy]

This is quite interesting, even though this is years old it still pertains it sounds like.
I now have 3600 miles on my 2020 RT Limited, and on the way home last night got a brake failure warning with code C0042.
I have looked through the repair manual I purchased, the owners manual, Lamonsters code page, and as of yet have not found what C0042 is.

I Turned the bike off, waited about 30 seconds, restarted it, and all lights were off and no more code showing on the screen.

[bluewoo]

Did you have your foot resting on brake pedal? I remember some having an issue with foot touching pedal long enough that the ECU throws a code.
Not sitting at a red light,but rather riding for miles and the brake pedal is slightly depressed.
Check the fluid level also.

[Azmi93]

Did you find the reason of this code i have the same issue like you have and when i shut it down the code and the brake failure message disapear and just in the next ride directly shows up again so any advices ??

[trikermutha]

Have you tried to bleed the brakes since you mentioned the pedal is soft.

[Manny64B]

[JohnRuckus]

I just received the code while out riding tonight. Is it safe to ride with this code?
The code cleared after I parked, and turned the spyder off and back on. I'm about 30 minutes from home. Its getting pretty cold out. BRP is supposed to be scheduling a tow, but I haven't heard back regarding the scheduled tow in about 30 min

[Freddy]

Generic C0042 Meaning
The Anti-Lock Brake System (ABS) Module monitors the Brake Pedal Position Sensor. The ABS Module sets the code when the Brake Pedal Position Sensor is not to factory specifications.

[JohnRuckus]

Thanks for the feedback! Sorry for the ignorance but does that mean no o shouldn't ride?

[JohnRuckus]

Welp,
Decided to ride her home. The fault didn't return. I'll take another ride tomorrow and try to get to the dealership to have them take a look.

[Lew L]

Check brake fluid level......... it's suprisingly sensitive.

[Joel The Biker]

I have posted about this previously. It is caused by the low pressure switch. There is a procedure for resetting it and must be done any time you bleed the brakes and turn the key on before pumping the brakes up hard. NEVER turn the key on during the bleeding process unless you have BUDS. If you do, you will get that code and need to go thru the reset procedure. I am not sure of the procedure now, but it is in the service manual.

[JohnRuckus]

That's the crazy part for me. I haven't done any brake work. I have about 220 miles on it. I guess it could be low brake fluid though. Thanks All!

[Joel The Biker]

Try this.
1 turn on ignition.
2 push brake pedal down as far as possible(should hear 2 clicks) and hold it
3 turn off ignition
4 release pedal
5 wait 30 sec then turn ignition back on. Fault code for LPS should be cleared.

This is straight out of the service manual

[JohnRuckus]

Thanks. I dropped it off at the shop the next day to have them take a look. while there, I'm having them take a look at a few other things. so, it will be there for a few days. passenger heated seat isn't heating. so, they'll look at that. Also, will address the fitment issues.
The other thing that I failed to mention is that after I pulled over, I engaged the parking brake, but it wouldn't disengage after pressing the button multiple times. I power cycled the ignition and the parking brake disengaged. Not sure if that is related or not, but just something to note.

[JohnRuckus]

So, it happened again last night in a parking lot. This time it was similar to a post where someone said it happened to their dad or someone and the parking brake engaged. Mine did the same. I wasn't traveling fast. I was at a rolling speed(less than 5mph). Someone mentioned a sensor reading and brake fluid levels. Not sure about that. This was the 4th time I've experienced this code C0042 since owning the spyder, and 2nd time since getting it out of the shop.
It is due for the 600 mile service. So I will bring it to the shop's attention again when I'm there.

[Snowbelt Spyder]

You should find another dealer. There is no 600 mile service on a 2020 RT.

3000 miles. Owners Guide, page 113.