Just installed a lift table that fits a spyder....

[rabtech]

It is a 1300 pound Kernel Trike lift. It gets it up in the air. Please ignore the mess. I was so tired after I put it together I just wanted to go inside and rest.

Sent from my Galaxy S3. I may have made a spelling error or may have some grammer issues. My fingers are way to big to type on this tiny screen!

[Bob Denman]

Oh; I am just sooo jealous right about now...
That is one Su-WEET-looking lift; do you have a link to where you can get them?

[rabtech]

I do. I dont think any sponsor sells them so here it is. I drove to the warehouse in Mississippi. I can tell you this guy has everything on this website in stock. He gave me a tour of the place and i was surprised to find everything actually in the building. The guys name is Ian Gilmore www.RedlineStands.com Redline Engineering LLC 3753 Compress Rd Como MS 38619. 901-351-4764 It is www.redlinestands.com. It was 1550.00 after I picked it up. They had to charge me tax because I picked it up locally. I recommend it highly. IT IS HEAVY! I mean seriously HEAVY!!!

I have a knee issue and when I was sliding around on the floor putting the Fox shocks on I just couldn't take it anymore. So I went inside and did the Ebay thing. Then I arranged the results by distance and found a company that I could drive to. I bought it Thursday evening and told him I would be at the warehouse the next morning at 8:00 when they opened to pick it up. I had to leave at 5:00AM but it was worth it.


Also , if anyone needs to use it and is in the North Alabama area you are more than welcome. Just PM me on here and ill get right back to ya.

[bullant12]

Senatobia MS is only 45 minutes away from my house... hmmmm

[rabtech]

Senatobia MS is only 45 minutes away from my house... hmmmm

It is actually in Como Mississippi. You will think you are lost. The it will just appear. Its a huge warehouse across from the Como Elementary School.

[Bob Denman]

Thanks for the info!
Now, I've just got to figure out how good I need to be until Christmas...

[rabtech]

I also bought the little scissor jack to lift the bike while on the lift. I will get pics of it later today. I have to put on the sway bar, smoothspyder backrest, and the akropovik exhaust.

[Pops]

That's a seriously fine looking lift!!

[Hberninger]

Once the Spyder is on the lift, does the center grey ramp and the center grey insert come off to gain access to the bottom of the front of the Spyder?

[Chupaca]

awesome lift. Great pics will have to start saving up...

[rabtech]

Once the Spyder is on the lift, does the center grey ramp and the center grey insert come off to gain access to the bottom of the front of the Spyder?

Yes all three ramps lift off and the center pulls out. You have to remove the center ramp to get the center gray part out. Yes you would have complete access to the bottom. Ill take pics in a little bit with it off and the ramps off.

[Flanker]

Bleep! I comin' over to your garage to work on my Spyder from now on. Lucky dog!

[coz]

can u get me a job where u work?

[SPYD1]

Nice lift an garage.

[rabtech]

can u get me a job where u work?

Work! Who has time for that when you have spyders to put farkles on.....

Seriously I probably should start saving more but I sure do like chrome and farkles. It may be the gold of the future. If it is I am going to have it made.....

[MrLooney]

Bob, Only way you can be good that long is to sleep until X~Mas Eve to get that new toy (lift)

[retirednick]

Sweet looking setup. No doubt will improve the maintenance cycle.

[bmwlarry]

I use Handy lift and love it but I really like the narrower rear end of the lift. Cuts down on reaching!

[rabtech]

I have mix feelings about the width. I am getting used to having a little extra table to lay my tools. Its not to deep to reach. I use a dr little rolling stool to roll around on and it will let me slide up to and even a little bit under the lift.

Sent from my Galaxy S3. I may have made a spelling error or may have some grammer issues. My fingers are way to big to type on this tiny screen!

[jerpinoy]

Love to have one