|
-
 Just ordered my BajaRon Anti-Sway Bar!
 After reading reviews on BajaRon's anti-sway bar, I placed my order. I will be installing on my 2012 RT.....
Hopefully the install will go smoothly!
-
Very Active Member
 Originally Posted by stallion143
After reading reviews on BajaRon's anti-sway bar, I placed my order. I will be installing on my 2012 RT.....
Hopefully the install will go smoothly!
A 2" long piece of 2x4 will hold the frunk just far enough out to change the bar. Make sure you center the bar.
JT
-
Active Member
Use the old bar to set the spacing of the stop callers. I used the box that the new bar came in to draw a traceing off the old bar. The distance from the ends to the stop callers inside dim. I think the spacing was 12 1/2 in. Good luck. Bob
-
Very Active Member
Originally Posted by stallion143
After reading reviews on BajaRon's anti-sway bar, I placed my order. I will be installing on my 2012 RT.....
Hopefully the install will go smoothly!
I used a Trolley jack under the "Very Front' of the trunk bottom and a few pumps and it lifts and moves the trunk away enough from the Bar .
2015 F3 sm6, Custom Dynamics fender lights.
Sea Doo GTI-SE 90 Jet Ski!!
-
Registered Users
Install is a snap--just follow his great directions. Then take it out and enjoy! 
-
SpyderLovers Sponsor
-
The anti-sway bar came in today! VERY fast service! Will do the install Friday morning...Wish me luck....
-
sway bar
The instructions are great just take time to follow them and its a snap also one of the best things I have ever done to any motor vehicle I have owned.
-
-
Registered Users
Going to put mine on tomorrow.
Well I got it on and it is raining all day.
Last edited by Grandpa Spyder; 05-18-2013 at 05:14 PM.
-
sway bar
I,am no merchanic and I put mine on in two hours going slower then norm but I jacked the front up onto a 4x6 and was able to work under the bike easier just read the instruction a few times and magic is done the bike is like nite and day cant believe BRP don't have it on automatically but glad Bajaron is a GENIUS and got it right
-
Test Run
OK....Did the install last Friday (as mentioned in a previous post)...
Finally got to try out today....Worth the $ and install time....
The RT rides much more stable now....Takes curves with very little effort!
Thanks Ron!
-
-
-
-
Active Member
Originally Posted by stallion143
After reading reviews on BajaRon's anti-sway bar, I placed my order. I will be installing on my 2012 RT.....
Hopefully the install will go smoothly!
Me too! Same reasons, just placed order. Looking forward to the "new ryde".
-
Originally Posted by stallion143
Most of the replies in regard to the installation of "The Bar" have mentioned lifting the RT using either an ATV jack or a floor jack...I think simple and just drove the  up on some car ramps, set the parking brake and then blocked the rear wheel. I DID use a short 2x4 to hold the frunk out of the way during the install...
BTW...The car ramp thing will work to install the "BumpSkid" too!
Oh boy, MORE farkling.....
Just my 2 cents worth! 
I did the same thing. Drove the up on car ramps and went to town. VERY EASY! You will be very pleased with the results. I had my bar for over a week before I had the time to do the install. Finally did it this morning. Like the others said, two hours to do the job and that includes several breaks for coffee and one phone call.
Good luck and enjoy the improvement.
-
BajaRon
Just ordered my BajaRon.. Can't wait.... Adjusted front shock to 5, I can feel the difference... Any rider in the RI area
-
Sway Bay
Installe Bajaron sway bar yesterday... Went for a ride... Ride nice... corners much better
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
Reply With Quote
Thanks to BajaRon for providing a SUPER product and GREAT detailed installation instructions!
Another confirmed case of Fakleosis... Get the Man's Mastercard limit raised! 
