Could someone who has one of the custom seats tell me the overall diameter of the fuel door as well as the diameter of the opening. I am thinking of adding one to my stock seat as a DIY project.
You can buy doors at some parts stores or online, but I'm not sure what size it needs to be.
Thanks
Ed
They told me not to give up on my dreams, so I went back to sleep.
Champagne 2017 RTS SE6
Quantum Blue 2012 RTS-SE5 "Bluebell, Bell for short" - Traded 09/2017
Could someone who has one of the custom seats tell me the overall diameter of the fuel door as well as the diameter of the opening. I am thinking of adding one to my stock seat as a DIY project.
You can buy doors at some parts stores or online, but I'm not sure what size it needs to be.
Thanks
Hi 2Paw, did you ever figure out your fuel door project? I am in the process of buying my first Spyder but not happy about the fuel filler under the seat. I like to camp and have always carried a duffle strapped to the back of my 2 wheelers. If I do that here I have to unstrap to get gas.
Could someone who has one of the custom seats tell me the overall diameter of the fuel door as well as the diameter of the opening. I am thinking of adding one to my stock seat as a DIY project.
You can buy doors at some parts stores or online, but I'm not sure what size it needs to be.
Thanks
I think it is quite easy to open seat to fuel up. I would think something on the side of the seat would bother me when driving.
I think it is quite easy to open seat to fuel up. I would think something on the side of the seat would bother me when driving.
I did a DIY fuel door , mine is much smaller than most others...O.D. of the mounting ring is only 4 inches, door is 3 1/8 in.........I don't even know it's there.........Mike
I did a DIY fuel door , mine is much smaller than most others...O.D. of the mounting ring is only 4 inches, door is 3 1/8 in.........I don't even know it's there.........Mike
Can you post a photo of the door? I'm thinking of doing the same.
Can you post a photo of the door? I'm thinking of doing the same.
Reg
Hi Mike here ....Bob Denman posted a PIC of His the other day on Thread after He returned from SPYDERFEST.........black on His Cognac RT.......It's not difficult to do.......A red hot nail to make your holes is the most important and then something to melt the seat material on the edge of the mounting ring. a Hole cutter for the big hole and drill or dremel with a very rough stone will take down the seat base very quickly.......Mike .....They sell the BiLLEt doors on E-bay $ 29.95 " Apex " makes a good one...............or E-Bay # 161801757548,,,, it's the same from a different seller
Last edited by BLUEKNIGHT911; 05-11-2016 at 09:45 AM.
Bob, did you do yours yourself, or did you have it done by someone else? And, what materials and technique were used to install it?
"A Wise Man Once Said, I Should Ask My Wife."
2017 Champagne Metallic RT-S SE-6 Rivco Dual Flag Holders; Slingmods Highway Pegs; (Hate Them) Airhawk Seat Cushion; Show Chrome Black Touring Rack w/ Risers & Touring Windshield; RAM X Mount For TXTAG; TackForm Phone Mount; Lidlox; Magic Mirror Mounts; Guardian Bells; WOLO "Bad Boy" Air Horn; Dual USB Power Outlet With Voltmeter; 12V outlet for misc. stuff; Spyderpops Full View Mirror Turn Signals; Large Brake Pedal; Kott Grilles; Large Mud Flap; BajaRon 3 Piece Sway Bar, Last But Not Least, Kuhmo Rear Rire, Vedrestien Fronts.
2017 RT-S , Brake pedal extender is twice the size of the stock pedal. Champagne Metallic
Mike put mine in for me. (I'm too much of a chicken, to cut on an expensive seat! )
If he chimes in; he can tell you what he used.
I was too busy covering my eyes, and crying like a baby!
Because of the seat PAN shape.......That hole required a 2 inch long machine screw and we just didn't have one......But I assured Him it wouldn't fall off........................Mike
I'm picking up the proper bolt for the job this week.
And I'll also try rotating the door counter-clockwise... even though it means drilling a hole!
Bob, I don't think you need to do this.........BUT - if you do .......heat up a large NAIL red hot and do it while the door is on with the other bolts in ..............Mike
2013 STL SE5 BLACK CURRANT
SpyderPop's: LED bumpskid
SmoothSpyder: dualmode back rest
T r * * LED:foam grip covers, Tricrings, FenderZ,
brake light strips, wide vue mirrors
Rivico SOMA modulation brake leds
sawblade mowhalk fender accents
minispyder dash toy
Lid lox
KradelLock
Pakitrack
GENSSI ELITE LED H4 headlights
FLO (Frunk Lid Organizer)
BRP fog lights, trailer hitch
SENA 20S EVO
Mike I think by now you must have done a few of these. It appears to me from the picture of Bob's bike that you have his mounted so the door opens up and to the left Does it open far enought to be out of the way? Would access be easier if it were rotated 180*? Does the door fold out of the way enough that it doesn't matter?
Happy TRAils/NSD
Paul
2012 RT L
AMA 25 years Life Member
TRA
PGR
Rhino Riders Plate #83
Venturers #78
TOI
Actually; I am going to rotate it so that it opens along a more horizontal plane.
Sometimes the gas nozzles get caught up on the hinge.
I think that if I move it by just one screw's location; it'll be perfect!
Mike I think by now you must have done a few of these. It appears to me from the picture of Bob's bike that you have his mounted so the door opens up and to the left Does it open far enought to be out of the way? Would access be easier if it were rotated 180*? Does the door fold out of the way enough that it doesn't matter?
The problem was.....when I mounted it ...the seat was up and this caused me to mis-calculate where it would end up.......Bob said leave it, He would adjust it later if needed..........................And nothing actually blocks the PUMP NOZZEL ....it's the RUBBER RING that is a slight issue, but not much IMHO..............................PS, the HOLES on the outside RING are all spaced apart the same distance.....so you can rotate the ring and get the HINGE where you want within those perimeters.......Ive had a bunch a PM's since doing this........Toooooooooo much typing ............Mike
Actually; I am going to rotate it so that it opens along a more horizontal plane.
Sometimes the gas nozzles get caught up on the hinge.
I think that if I move it by just one screw's location; it'll be perfect!
Bob have you found the matching screw at Home Depot ???? the package is Green , hanging on the wall....#10 - 24 X 2in
boy, that fuel door is a great idea.. are there any pics showing the fuel door open? or maybe a pic from below? .. i am assuming the seat still travels up and down if needed..
i would be installing this on a 2014 rs .. thanks guys ... chuckk ..