-
Hindle pipe installation
Installation took 10 minutes. This is what I did. Removed the bracket nut & bolt, remove header pipe clamp, remove retainer spring on front side of header pipe, slide old muffler off gently, remove asbestos sealer collar on header pipe, install new header pipe collar, carefully slide hindle exhaust over head pipe being careful not to damage the much thinner new sealing collar, attach bracket mount bolt & spacers, use red loctite on mounting bracket nut, make sure new pipe is fully on the head pipe. Hook retainer spring onto head pipe, using vise grips extend spring to hook into retainer spring eye on hindle pipe. Be careful not to injure yourself. Make sure everything is aligned properly before tightening pipe clamp. Mount pipe clamp so that it does not protrude below the lowest level of the head pipe. Tighten securely according instructions that came with hindle pipe. Start motor and check for exhaust leaks around new pipe seal. If any, re-tighten until gone. Let idle 10-15 minutes to "burn in" new muffler pipe. Let cool, start motor again run 5-10- minutes checking for exhaust leaks again. Now ride- it sounds GOOD ! Spyder running 2+ bars cooler.
You can do this !
-
SpyderLovers Founder
-
-
Re: Hindle pipe installation
Originally Posted by 2faston3
I love a lady who is handy with a wrench. :bigthumbsup:
As the old saying goes, if you can't find a rich gal, find a "wrench" gal. :
2faston3
Owning a Spyder means she IS a rich and wrenchy gal ;D
-
Re: Hindle pipe installation
Thanks everyone ! RocketLady is married to Rocketman, and with his direction on the hindle install. He is a marine tech and I assist him in our own business. :bigthumbsup: Today we are installing Ken's new brake light turn signal conversion. This installation is just a "Plug & Ride". I ride the Spyder, he still rides his Yamaha FJR, but has got caught up in a Spyder web.
-
Re: Hindle pipe installation
Originally Posted by RocketLady
but has got caught up in a Spyder web.
Nicely said
-
Active Member
Re: Hindle pipe installation
:bigthumbsup:Very good enfo on the intall , i am waiting to get my Hindle and it is nice to know it is an easy install. Thanks for the the good feedback.
-
Re: Hindle pipe installation
Originally Posted by RocketLady
Installation took 10 minutes. This is what I did. Removed the bracket nut & bolt, remove header pipe clamp, remove retainer spring on front side of header pipe, slide old muffler off gently, remove asbestos sealer collar on header pipe, install new header pipe collar, carefully slide hindle exhaust over head pipe being careful not to damage the much thinner new sealing collar, attach bracket mount bolt & spacers, use red loctite on mounting bracket nut, make sure new pipe is fully on the head pipe. Hook retainer spring onto head pipe, using vise grips extend spring to hook into retainer spring eye on hindle pipe. Be careful not to injure yourself. Make sure everything is aligned properly before tightening pipe clamp. Mount pipe clamp so that it does not protrude below the lowest level of the head pipe. Tighten securely according instructions that came with hindle pipe. Start motor and check for exhaust leaks around new pipe seal. If any, re-tighten until gone. Let idle 10-15 minutes to "burn in" new muffler pipe. Let cool, start motor again run 5-10- minutes checking for exhaust leaks again. Now ride- it sounds GOOD ! Spyder running 2+ bars cooler.
You can do this !
-
Re: Hindle pipe installation
Originally Posted by Roaddog2
New thinner collar? My Hindle came without new collar, also not mentioned in the instructions.
So are there Hindles with and without collars???
-
Very Helpful Member
Re: Hindle pipe installation
Hmm... Our Hindles that we got last week didn't have a collar either and also, nothing about it mentioned in our installation instructions.
Former Happy Spyder Owner
Just decided it was time to move onto other things.
-
SpyderLovers Founder
Re: Hindle pipe installation
Originally Posted by bjt
Hmm... Our Hindles that we got last week didn't have a collar either and also, nothing about it mentioned in our installation instructions.
Sounds like there were some changes mid stream because I think Tharkin said he did have to remove the old gasket.
-
Very Helpful Member
Re: Hindle pipe installation
Originally Posted by Lamonster
Sounds like there were some changes mid stream because I think Tharkin said he did have to remove the old gasket.
I agree that there must have been changes in the pipes. We did have to remove the stock muffler's gasket from the header pipes but the Hindle did not come with a thinner gasket or collar. It just slid right onto the pipe... :arrow: You know, come to think of it, she must have been talking about the clamp that straps the Hindle pipe to the header pipe. That is smaller as the Hindle pipe is a smaller circumference than the stock pipe. We just needed to get our terminolgy straight. 8)
Former Happy Spyder Owner
Just decided it was time to move onto other things.
-
Re: Hindle pipe installation
I just got and installed my Hindle. Took all of about 20 mintues to take off and on the new one. No gasket and the existing had to go..no way the pipe will fix. Not going happen..simple math there. I put it on..tighten the collar and have a small leek. Adjusted until the cows came home and the leak just moves with where ever the gasket is when I move it. Have not tried any sealent but going to run up the street and try and get some.
As for the Spring, there is NO way that spring is going to connect unless I stretch it out. The spring holder on the hindle is on the top of the pipe and the one on the header is on the bottom..Umm..I don't think I can install it upside down..lol. HELP..
Very Happy Owner
-
Re: Hindle pipe installation
Originally Posted by spydernrdu
I just got and installed my Hindle. Took all of about 20 mintues to take off and on the new one. No gasket and the existing had to go..no way the pipe will fix. Not going happen..simple math there. I put it on..tighten the collar and have a small leek. Adjusted until the cows came home and the leak just moves with where ever the gasket is when I move it. Have not tried any sealent but going to run up the street and try and get some.
As for the Spring, there is NO way that spring is going to connect unless I stretch it out. The spring holder on the hindle is on the top of the pipe and the one on the header is on the bottom..Umm..I don't think I can install it upside down..lol. HELP..
At my 625 mile service, the dealer sealed the pipe w/silicone. There's a noticeable difference (to me) in acceleration; it's much more responsive with less throttle.
I'll try to get a pick of my Hindle and the spring tonight and post it up. Maybe it'll help.
Happy Spyder Owner - 2008 Millennium Yellow PE #2475
HID lights, fog lights, Hindle exhaust, heated grips, anti-vibe bars, passenger extension pegs, BRP custom seat, seat cowl, sport rack/backrest, BRP saddlebags, CHAD black/smoke windshield, outdoor cover, Garmin Quest GPS, Rear axel billets.
-
Just found this on U-Tube and thought it may help so I posted it here.
I find reading other's post more informative, but every little bit helps right?
[nomedia="http://www.youtube.com/watch?v=Y9g2oUhl_nE&feature=related"]YouTube- Broadcast Yourself.[/nomedia]
Mark
-
Very Handy Member
Originally Posted by SpyderByter
Just found this on U-Tube and thought it may help so I posted it here.
I find reading other's post more informative, but every little bit helps right?
YouTube - Hindle install
Mark
Yup, that would be bjt installing my Hindle
With Christ all things are possible, so live life with no fears and no worries.
Happy Ex Owner, Hopefully future Spyder owner again.
Pastor Deb Tangen, Missions Director and short term missionary.
-
Thanks for that. I read all the posts concerning the Hindle install (and problems with) and saw your vid back when I was looking for sound comparisons before I ordered the Hindle. I remembered seeing it so I searched it out again today, then posted it here so anyone getting ready to do it can benefit from you taking the time to document it. They say a picture is worth a thousand words.
I got a lot out of the posts also, because right off the bat, I used a sealant to avoid any leaks. In your vid, it looks like bjt put the spring back on. The instructions make no mention of reinstalling the spring, and it looks like the clips don't line up. I did not put it back on yet. I figure that can always be done later. I guess the extra tension would help to ensure it stays seated. Now it sits for 24 hours for the sealant to cure, then I season the muffler.
I should add that the instructions don't say this, but I noticed that the allen bolt that holds the muffler up had locktite on it, so it only makes sense to use locktite when reassembling.
Last edited by SpyderByter; 04-10-2009 at 06:54 PM.
-
I also read in one of the posts, someone disconnected the battery. Is this necessary? I know it is with some other mods for the puter to relearn (remap?), but I thought the Hindle was not one of those.
-
Very Helpful Member
Originally Posted by SpyderByter
I also read in one of the posts, someone disconnected the battery. Is this necessary? I know it is with some other mods for the puter to relearn (remap?), but I thought the Hindle was not one of those.
I think its a good idea with the Hindle also. Any free flowing exhaust can affect the way the engine runs. Its easy to just disconnect the battery, install the Hindle, then reconnect the battery.
-
Ok, thanks, will do before I run it to season it.
-
Where is the best place to purchase the Hindle for the Spyder?
-
Originally Posted by trikester
Where is the best place to purchase the Hindle for the Spyder?
Trikester see if this one is still available here from one of our members.
http://www.spyderlovers.com/forums/s...ead.php?t=9460
Diggittt
Full Moon #1176
Talon Alarm
Trunk Spring
Power Bus
H.I.D. Headlights
Kuryakyn ISO Grips
NMN Highway Brackets
Kuryakan Highway Pegs
Two Brothers Dual Exhaust
BRP Sports Rack & Back Rest
LED Fender Tips
Ride-On
BRP Tank Bag
H.I.D. Fog Lights
Sirius Satellite Radio
GlowRyder L.E.D. W/Remote
TricLed Fender Lights
-
Originally Posted by trikester
Where is the best place to purchase the Hindle for the Spyder?
I think Bonecrusher has a source that is the cheapest I have seen. Might PM him.
-
I just put the hindle exhaust on this afternoon and it sounds great. I can't believe how much heavier the stock exhaust ways and how constricting it was. The videos on youtube.com dont do the hindle any justice of how low it actually is. I can't image how much louder the two brothers twin pipe sounds like.
-
MOgang Member
hindle
Where did you buy your hindle exhaust from? I am on the market to get one!!
Thanks in advance
Joe
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|