-
Breakfast meet Sunday June 10th
Anyone want to meet up and ride down to the woodstown dinner or another place , kountry kitchen ? Open to suggestions .
What time ? meet anytime like 7:30 am ?
Who knows that area for the ride ?
Ken , we can figure a meet up point for the ride down . Like mayslanding McDonald's . Need to see who else would like to go to meet up other places on the way .
Another day for breakfast , I enjoy the smithville bakery . Nice ride from down my way .
Who going so far :
1- Dwanton
2 - kentompkins
3 - drewnj
4 - spyder3
5 - boriken
6 - poopman (meet us there)
7 - mrmichaelg
Last edited by Dwanton; 06-09-2012 at 12:14 PM.
-
Active Member
Sorry, Dwanton, I didn't see that you had started a new thread.
Can we meet at the Woodstown Diner at, say, 10:30? I have a 70 mile route planned through Mays Landing, Millville, Parvin State Park over to Woodstown. Trying to avoid Rt. 40. Happy to share it so others can find a join-up point.
Realize it's a late plan but perhaps some of you are free.
kt
Originally Posted by Dwanton
Anyone want to meet up and ride down to the woodstown dinner or another place , kountry kitchen ? Open to suggestions .
What time ? meet anytime like 7:30 am ?
Who knows that area for the ride ?
Ken , we can figure a meet up point for the ride down . Like mayslanding McDonald's . Need to see who else would like to go to meet up other places on the way .
Another day for breakfast , I enjoy the smithville bakery . Nice ride from down my way .
-
Registered Users
Is any one coming near Williamstown on Sun so i can meet up with them ?
-
Active Member
Michael.....
In case you can't link up with someone, if you take the Clayton/Williamstown Rd over to Clayton and then take County Road 610 to CR 619, that will take you to Rt 40. Hang a right there and that goes right into Woodstown and right by the diner.
Or you could take Rt 55 south to Millville and meet me there and we can then proceed on my route to Woodstown. That way, you'd get more riding in.
Either way, I hope you will join us. The weather is too good not to ride.
I'll send my route in an email so you can see where I'm planning on riding.
kt
Originally Posted by mrmichaelg
Is any one coming near Williamstown on Sun so i can meet up with them ?
-
Very Active Member
KT.what's your approx. ETA at Milville?
Last edited by Boriken; 06-08-2012 at 05:04 PM.
-
Ken what route are you taking to get to Millville , at some point you will be cruising past me .
I don't know any back roads to meet up with mrmichaelg , I would find my way onto rte55 and get off on rte40 over to the woods town dinner . For williamstown I would take old tuckahoe rd that ends up onto rte322 by turnersville auto complex .
I don't mind meeting up where ever . Boriken is from capemay and i can meet him on rte55 or I can meet mrmichaelg somewheres . Or just meet up with ken coming past my way .
Either way I am going riding
-
I'm not going the route of the mall so I figure I will just meet you guys in woodstown. Have a safe ride in.
John, however you want to go is fine with me. Just let me know if your meeting up with me or going east toward the mall before heading toward woodstown. I am good either way.
I also have a good spyder friend riding up from Delaware to meet up with us in woodstown. Looking like this will be a good meet up for sure. Looking forward to it!
Sent from my iPhone using Tapatalk
-
Very Active Member
ok, i thought you were closer to the mall. Lets leave it the way it was. Doug, i will see you at the wawa at what time?
Rewaco RF-1 GT
Inline 4 cylinder Ford Zetec with multi-port fuel inject, 140 HP
0-60mph: 5.8 seconds
5 speed sync manual with reverse, mechanical dry clutch.
Front suspension: Trapezoidal fork with center spring
Rear suspension: Independent with Bilstein gas shock absorbers
Brake System: Grimeca calipers, linked ventilated discs, with booster
10.57 gallons
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|