-
Active Member
-
It is definitely a known issue that the Up n Out Mirrors will not work with a stock Ultra Touring Shield. I believe that ESI even notes that somewhere on their site.
As for cutting it, many here have modified shields so I am sure you will get some assistance.
Good luck.
-
GOS member (Girls On Spyders)
That's a bummer.
I need something to improve the mirror functionality and I like the Up & Outs, but, I have the touring windshield.
Might have to wait and see what the new KewlMetal extensions look like.
-
had similar problem. so i asked my service department to trim for me. he cut with a saw and then smooth out the edges. they (east coast cycle in Ben Salem Pa), did a great job trimming for me.
-
Server Admin
I have cut and modified many shields and had no problem. Use a fine blade on jigsaw, moderate speed. Line area around cut with masking tape so that the jigsaw does not scratch it. Sand the cut with high speed orbital sander, about 400 grit. With a little care the surface will be as good as the factory cut. Some plastics will bend with a heat gun better than others, you just have to try and see. Too much heat is the problem, say take you time!
-
Alignment Specialist
Some have said that if there are any marinas near you, they do a great job with this type of thing...I didn't check what state you're in, but something to think about if you're near boats...
Bone Crusher
If you work to make money, you'll never be happy, as there's never enough money...if you work to take good care of people, the money will always be there....Sean O'Connell, 1999
-
Active Member
Thanks everyone, for your input. Macsmonster, this will be the first. I follow what you've given here. I have a very fine toothed blade for my scroll saw and the 400 grits paper for the orbital sander.
-
Registered Users
Best of luck! I hope the windshield modification works out well for you. My wife also loves her Up and Outs.
-
Active Member
-
SpyderLovers Founder
Looks good but do you need to cut more to get the top bolts in?
-
Registered User
Originally Posted by 1VENOM
Thanks for everyones input. I held my breath, and did the cut and sand modification to the Ultra Touring Windshield today. First time trying to cut any plastic, that really mattered. Tell me what you think.
Very, very nice.
MM
[URL="http://www.esicycleproducts.com/"]
-
Active Member
Looks good but do you need to cut more to get the top bolts in?
No, once I modified the bottom of both wings, it fit without having to modify the mounting holes. I was worried that doing a modification to the mounting holes may weaken the whole windshield.
Last edited by 1VENOM; 04-19-2010 at 03:32 PM.
-
Looks terrific! Think I'll try it!
-
Thanks for this venom, subscribed. Will need it when I install my up and outs.
-
Very Active Member
Great looking ryde, nice job.
"Stupid is as Stupid does"
Don't Drink and Drive or Ryde!
Each Day is a Gift
-
Registered User
Originally Posted by Hesstx
Not slamming ESI but where ever this is written maybe it should be an large type. I do most of my own work I dont like to cut shields so will have to pay to have it done. this just add to a fairly expensive product
Your shield does look great!
It's OK if you want to send them back just give us a call and we can give you a credit for these right away..
It's not on our site what sheilds it does or does not work with as their are many we have never seen first hand and have no way of knowing all the combos out there.
However it's not on BRP's that their sheilds won"t work with our extensions ether.
MM
Last edited by Magic Man; 04-20-2010 at 03:21 AM.
[URL="http://www.esicycleproducts.com/"]
-
Registered Users
You did a great job cutting that screen!
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|