-
2020 RT Ltd seat won't stay up when filling gas etc - any ideas?
My seat won't stay up when getting gas or checking oil. I don't see anything to latch or hold it up?
Help please.
-
There is no latch, or "prop rod" on a 2020 model. The seat is, or should be, held up by a single pressurized gas shock mounted to a plastic pin on the left side hinge arm. Raise your seat, inspect that connection to see if the pin broke off or the shock has lost pressure.
If your still under warranty, check with your dealer to see if a worn shock is considered "normal wear & tear & you foot the bill, or if BRP will replace it FOC.
2020 Spyder RT Limited; Deep Marsala/Chrome
Formosa AZ01 165/50/R16's on PPA Recluse wheels up front
General Altimax RT43 215/60/R15 on factory rear
Primary exhaust: RLS Cat delete w/ his baffle; secondary, custom built w/ Flowmaster HS2
Suspension: BajaRon swaybar (highly recommended!), M2 coil-overs, front & rear (also highly recomended!)
Extra LED lighting and misc. to suit my needs/wants
-
Very Active Member
If you get that shock in your hand, then you can go to napa if you have them around you or go to https://www.mcmaster.com They will have what you need
-
When riding my 2021 in rain the seat will not stay up on its own but once the seat dries out good it will again hold the seat up. My point is the OEM strut is barely stout enough to hold up the seat, doesn’t seem to be able to support any additional weight at all.
Last edited by Adventurer; 05-08-2022 at 09:34 AM.
Reason: Clarification
2021 Spyder RT Limited (Sea-To-Sky)
2022 Ryker Rally
-
Very Active Member
If the shock is still attached, you may need to replace the shock with a stronger weight spec (30lb). If the seat is soaked (or you have a cover/pad) the added weight may be the problem.
'20 Spyder RT: Bajaron swaybar. Vredestein tires, Pedal Commander, Elka front shocks, GPS/USB/12V handlebar mount, Heli-Bars, Radar Detector, KOTT grills & vents, Shad top case, chin & DRL LEDs.
-
Very Active Member
Originally Posted by RayBJ
If the shock is still attached, you may need to replace the shock with a stronger weight spec (30lb). If the seat is soaked (or you have a cover/pad) the added weight may be the problem.
Yes, mine won’t stay up even with just a small sheepskin topper on it Ray. I can’t imagine that strut will go anywhere near coping with my soon to arrive Russell Daylong seat.
Pete
Harrington, Australia
2021 RT Limited
Setup for Tall & Big.... 200cm/6'7", 140kg/300lbs, 37"inleg.
HeliBars Handlebars
Brake rubber removed to lower pedal for easier long leg/Size 15 EEEEW boot access.
Ikon (Aussie) shocks all round.
Russell Daylong seat 2” taller than stock (in Sunbrella for Aussie heat & water resistance)
Goodyear Duragrip 165/60 fronts (18psi) - provides extra 1/2” ground clearance.
Kenda Kanine rear.
2021 RT Limited , Brake pedal rubber removed for ease of accessing pedal with size 15 boots. Red
-
Very Active Member
-
SpyderLovers Ambassador
Safety Issue? ?
l just figured it out (seat strut).
Safety Issue is what came to mind.
Then I could be totally wrong.
1. Please be sure that you have nothing on your Spyder Seat.
2. Also it must be completely dry.
3. Then you should be able to get the Seat to stay up with the OEM Strut.
4. If not, then replace the Seat Strut.
Thanks and I hope you have a Sunny Day. .....
ENJOY YOUR LIFE WITH A SPYDER
Ryde with a Friend and be Safe
My Spyder ..... 'Little Blue-Boy'
-
Very Active Member
,And don't open it on the fourth Wednesday of the month!!!
-
Very Active Member
A little stick, or dowel, of the right length to suit works fine. Lay in underneath the seat afterwards.
Two Wheelers from 1963-2011
Three Wheelers:
2011 RT(Red)
2014 RT(white)
2016 F3T(red)
2022 RT current ride(silver)
__________________
2016 Slingshot
2018 Vanderhall
2019 Slingshot
-
Active Member
Here is the real fix. 100% total comfort PLUS a gas door. Never lift the seat again to fill the fuel tank. True it is more costly than that cheezy arm thing.
https://ultimateseats.ca/can-am-spyd...2020-and-newer
Last edited by Peter Aawen; 05-10-2022 at 08:15 PM.
Reason: Fixed link ;-)
-
I just looked through K80's advice on strut replacements; IMO, not sure anyone could do better and it would be my guide to replacing that strut.
2020 Spyder RT Limited; Deep Marsala/Chrome
Formosa AZ01 165/50/R16's on PPA Recluse wheels up front
General Altimax RT43 215/60/R15 on factory rear
Primary exhaust: RLS Cat delete w/ his baffle; secondary, custom built w/ Flowmaster HS2
Suspension: BajaRon swaybar (highly recommended!), M2 coil-overs, front & rear (also highly recomended!)
Extra LED lighting and misc. to suit my needs/wants
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|