-
Is there a Video on how to install Baja Ron’s sway bar on a 2020/2021 Spyder RT?
Baja Ron’s sway bar is there a how to install video on a 2020 / 2021 Spyder RT?
Jim
-
Very Active Member
When I got my bar from Ron, he had a very good instruction sheet it the box!! The job looks worse than it really is!! Good luck!! You can do it
-
Completely agree with Mikey. Assuming you bought it new and got the instructions, just follow those. It's simple. The hardest thing is getting the front of the bike high enough. You remove (2) belly panels then just follow the instructions to remove the old and install the new.
-
Very Active Member
Agree with all the above. It's not hard at all, but you MUST have the required height or you will not get the old bar out and new bar in.
-
SpyderLovers Sponsor
Originally Posted by Jetfixer
Agree with all the above. It's not hard at all, but you MUST have the required height or you will not get the old bar out and new bar in.
Very true. Some imagine there is a way to cheat that height. But once you get there, you find there is no way around it. Get it up, or you won't get it out! Still, an easier job than most think. It's only hard if you try to hurry.
Shop Ph: 423-609-7588 (M-F, 8-5, Eastern Time)
Only SLOW people have to leave on time...
-
Very Active Member
Some have used planks to ride up a slope for the clearance needed. You can lift a little lower if you only raise the front because the angle gives more room for removal.
'20 Spyder RT: Bajaron swaybar. Vredestein tires, Pedal Commander, Elka front shocks, GPS/USB/12V handlebar mount, Heli-Bars, Radar Detector, KOTT grills & vents, Shad top case, chin & DRL LEDs.
-
SpyderLovers Sponsor
Originally Posted by RayBJ
Some have used planks to ride up a slope for the clearance needed. You can lift a little lower if you only raise the front because the angle gives more room for removal.
True, that kind of 'Cheating' will buy you some extra room with less lift.
Shop Ph: 423-609-7588 (M-F, 8-5, Eastern Time)
Only SLOW people have to leave on time...
-
Active Member
I took the Baja Ron bar off my 2019 and installed it on the 2021 RTL w/o instructions. It's a pretty straight forward install. As others have said as long as you have the hight to remove it after it is unbolted.
2021 RTL Chrome Deep Marsala
HELI Bars
Garmin Zumo XT
USB power port
Front fender lights & Sequential turn signals
Front LED Auxiliary light
Flashing brake module TricLED
Baha Ron sway bar
belt tensioner
RLS muffler
-
How far does it need to be lifted?
-
SpyderLovers Sponsor
Originally Posted by Valiant
How far does it need to be lifted?
You need 24" of vertical clearance from the sway bar mounting channel to the ground. You start with about 4-5 inches because the bar is tucked up from the ground that far. So, that means you need to get about 20" more. However, as mentioned above, if you lift just the front of the bike (which I recommend because leaving the rear wheel on the ground gives you added stability). The angle means you get more room vertically from the Spyder to the floor with less lift. Then you are looking at more like 18" of total lift.
Last edited by BajaRon; 05-04-2021 at 07:58 AM.
Shop Ph: 423-609-7588 (M-F, 8-5, Eastern Time)
Only SLOW people have to leave on time...
-
Very Active Member
Could I use the ramps that I use to load my lawn tractor on the back of my silverado to get the desired height with the rear wheel on the ground?
I really have no desire to use any jacks or jack stands on my spyder.
2020 F3 SE6
Safety and Lighting: LED Headlight upgrade, IPS LED Fog lights, Show Chrome LED Fender Signals, LED Signature Light, Tric LED Afterburnerz, MotoHorn 2.0
Suspension: Wilbers Front and Rear Shocks, BajaRon Sway Bar, Vredestein Quatrac Front and Rear Tires
Comfort: Blue Ridge Windshield, Corbin Dual Touring Saddle, Ultimate Floorboards, OEM Passenger Backrest with Rear Shelf, OEM Passenger Floorboards Modified with High Risers from Pierre
Tackform Center Mount Phone Holder w/ rapid charging USB-C.
-
Very Active Member
Originally Posted by CloverHillCrawler
Could I use the ramps that I use to load my lawn tractor on the back of my silverado to get the desired height with the rear wheel on the ground?
I really have no desire to use any jacks or jack stands on my spyder.
Yes, another member on here has done that with no problem.
-
Active Member
-
Active Member
When I installed the sway, I used a forklift, right under the A-arms, with a rubberblock between the gables and the spyder. worked like a charm.
the funniest thing about this particular signature is that by the time you realise it doesn't say anything it's to late to stop reading it........
Spyder F3s 2019 All Black ( Named it: Brutus)
Carbon Items added, just for looks
Upgraded Shocks Trac-Tive, Rear hi/lo and rebound adjustable, with Hydraulic Pre-Load adjuster
fronts hi/lo and rebound adjustable, custom made by the Trac-Tive Guru's
Swaybar (Ron's)
Tyres Front Michelin Cross Climate+ 175/60-15
Rear, for 2022 still a Kenda, next Yokohama Advan Fleva 205/55R15
Exhaust Bone stock, with a RLS Cat- Delete
Custom ECU-Mapping, rewritten/adapted to my Ridingstyle
Pedalbox, Awesome Upgrade...
Forum
RT Shop Talk
Is there a Video on how to install Baja Ron’s sway bar on a 2020/2021 Spyder RT?
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|