-
Active Member
Reusing RT-622 Trailer with 2020 RT Limited
Has anyone reused a Can-Am RT-622 trailer with a 9 pin round connector with a new style 4 pin square on the Rt’s? I just traded in my 2010 RTS for a 2020 RT Limited and kept the trailer. I was hoping to find a pre-made pigtail of some sort. If not I will cut the old connector off and hardwire the 4 pin square on. thanks Bob
Bob H - Derry, NH
2020 Spyder RT Limited - Petrol Metallic Blue
2010 RT622 Trailer and BRP Hitch
BRP Vented Touring Windshield, BRP Backrest
Garmin 590 with BRP Mount
Fobo TPMS for Spyder and Trailer
Lidlox, Blue Sea Fuse Box for power distribution
Ram Ball Mounts for Radar Detector, Cup Holder and Phone Holder
Sena 20S / SL2 Headsets, Foam Grip Covers, Belt Tensioner
BAJA Ron Sway Bar and Shock Adjusters, Heli Bars
-
Very Active Member
What you propose is doable, but there is a better way. If you purchase the oem trailer tongue wire harness, you should be able to do a simple plug and play with minimal to go with 4 pin square.
The trailer wire harness was reasonably priced.
Ensure too, your RT622 has the grounding wire upgrade if applicable.
-
RT-S PE#0412
Originally Posted by PMK
What you propose is doable, but there is a better way. If you purchase the oem trailer tongue wire harness, you should be able to do a simple plug and play with minimal to go with 4 pin square.
The trailer wire harness was reasonably priced.
Ensure too, your RT622 has the grounding wire upgrade if applicable.
Yes, I ordered it for $79 and got 10% off from the dealership.
-
Active Member
Thanks PMK. Do you have p/n's of the harness and the ground wire upgrade?
Bob H - Derry, NH
2020 Spyder RT Limited - Petrol Metallic Blue
2010 RT622 Trailer and BRP Hitch
BRP Vented Touring Windshield, BRP Backrest
Garmin 590 with BRP Mount
Fobo TPMS for Spyder and Trailer
Lidlox, Blue Sea Fuse Box for power distribution
Ram Ball Mounts for Radar Detector, Cup Holder and Phone Holder
Sena 20S / SL2 Headsets, Foam Grip Covers, Belt Tensioner
BAJA Ron Sway Bar and Shock Adjusters, Heli Bars
-
Very Active Member
Originally Posted by upsdoctor
Thanks PMK. Do you have p/n's of the harness and the ground wire upgrade?
Yes, just to be clear, your new Spyder has the 4 pin square and you have a round pin trailer harness.
You are wanting everything updated to 4 pin square.
If you pm your email, I should be able to send the applicable instructions that will update the trailer to the later setup which is worth doing also to prevent any concerns about electrical issues.
You did not post the model year of the trailer. Please supply that and the document will make more sense.
-
Very Active Member
Just beware that 2010 BRP Trailers had a problem with the ground wire, make sure you get a good ground and rewire the end fitting on the trailer to match your spyder.
Cruzr Joe
2018 F3 Limited, BRP Driver Backrest, Spyderpops Lighted Bump Skid, Dual Spyclops Light, Mirror Turn Signals, Laser Alignment, Engine LEDs, Fog Lights With Halo's, Cushion Handgrips, BRT LEDs, and Under Lighting, Lamonster IPS, (with Clock), F4 25" Vented Windshield with Wings, Airhawk "R" Cushions. Position 4 Brake setting, Short reach Handlebars, Dash Mounted Voltmeter and 12 Volt Plug. Set of 3rd pegs. Extended Passenger Seat. Exterior BRP Connect setup, Ultimate Trailer
-
Hi,
I have the same problem. But i have Spyder Rt 2010 with 9 pin round connector and i buy a trailer Freedom 2013. The trailer have 4 pin square connector. Is it possible to change only the oem trailer tongue wire ?
Thanks
-
SpyderLovers Sponsor
Yes, it will change over.
Joe Meyer
Dealer for the Outlaw/ROLO laser Alignment system
-
Very Active Member
Originally Posted by Stephan
Hi,
I have the same problem. But i have Spyder Rt 2010 with 9 pin round connector and i buy a trailer Freedom 2013. The trailer have 4 pin square connector. Is it possible to change only the oem trailer tongue wire ?
Thanks
If you have a 2010 trailer, there is a wiring upgrade kit that needs to be installed as part of converting to the square plug. This includes a ground wire upgrade and disabling certain lights.
-
Very Active Member
I have a BRP trailer upgrade kit that I need to post in the for sale section... part number 219400271.... converts the trailer 9 pin to flat 4.... then you just need an adapter from the 4 flat to 4 square... I will likely post it at $75 plus shipping if you are interested.
2017 Can Am Commander Limited
2012 Cadillac CTS-V Black Diamond
2020 F3 Limited Magma Red (miss the 2011 Viper red)
2010 RT622 - Black
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|