-
Very Active Member
SENA Cavalry Helmet, FACESHIELD???
Do you know where i can get a face shield for the SENA cavalry half helmet???
Cruzr Joe
2018 F3 Limited, BRP Driver Backrest, Spyderpops Lighted Bump Skid, Dual Spyclops Light, Mirror Turn Signals, Laser Alignment, Engine LEDs, Fog Lights With Halo's, Cushion Handgrips, BRT LEDs, and Under Lighting, Lamonster IPS, (with Clock), F4 25" Vented Windshield with Wings, Airhawk "R" Cushions. Position 4 Brake setting, Short reach Handlebars, Dash Mounted Voltmeter and 12 Volt Plug. Set of 3rd pegs. Extended Passenger Seat. Exterior BRP Connect setup, Ultimate Trailer
-
Very Active Member
Originally Posted by Cruzr Joe
Do you know where i can get a face shield for the SENA cavalry half helmet???
Cruzr Joe
I’ve been looking, but have found nothing and have been told there is nothing. Still looking, though.......
Tri-Axis Chrome Handlebars
Sena SM10 BT Dongle
Double USB Port/Volt meter
LaMonster Magic Mirrors
BajaRon Swaybar
HALO Skid Plate
Spyder Pops Rear Running Lights Turn Signals/Brake Light
Spyder Pops Mirror Running Lights/Turn Signals
Shorty Antenna
LaMonster Cat Delete
Akrapovic Muffler
FOBO2 TPMS
Rear Trunk Rack
Bruce Erickson
Chilliwack, BC
Canada
You know when a politician is Lying. It's when his lips are moving!
2014 RTS-SE6 - Cognac
intro to m/c 1949 Royal Enfield 500cc thumper
-
SpyderLovers Sponsor
I have had people tell me they have found them at Cycle Gear.
you must remove the visor and snap on the face shield using the same
snaps on the helmet as the visor.
Last edited by Motorcycledave; 06-23-2020 at 07:26 PM.
-
Very Active Member
Dave, there are no snaps...only screws. I have seen, as a matter of fact “have” the ones with snaps, and gthey are not wide enough to even think about fitting.
Tri-Axis Chrome Handlebars
Sena SM10 BT Dongle
Double USB Port/Volt meter
LaMonster Magic Mirrors
BajaRon Swaybar
HALO Skid Plate
Spyder Pops Rear Running Lights Turn Signals/Brake Light
Spyder Pops Mirror Running Lights/Turn Signals
Shorty Antenna
LaMonster Cat Delete
Akrapovic Muffler
FOBO2 TPMS
Rear Trunk Rack
Bruce Erickson
Chilliwack, BC
Canada
You know when a politician is Lying. It's when his lips are moving!
2014 RTS-SE6 - Cognac
intro to m/c 1949 Royal Enfield 500cc thumper
-
Very Active Member
-
Very Active Member
2018 F3 Limited, BRP Driver Backrest, Spyderpops Lighted Bump Skid, Dual Spyclops Light, Mirror Turn Signals, Laser Alignment, Engine LEDs, Fog Lights With Halo's, Cushion Handgrips, BRT LEDs, and Under Lighting, Lamonster IPS, (with Clock), F4 25" Vented Windshield with Wings, Airhawk "R" Cushions. Position 4 Brake setting, Short reach Handlebars, Dash Mounted Voltmeter and 12 Volt Plug. Set of 3rd pegs. Extended Passenger Seat. Exterior BRP Connect setup, Ultimate Trailer
-
SpyderLovers Sponsor
Originally Posted by bigbadbrucie
I’ve been looking, but have found nothing and have been told there is nothing. Still looking, though.......
Hey Chilliwack...... call me if you can I can tell you how to put the face shield on the helmet using the same holes that are in it
209-887-3283
-
Very Active Member
Originally Posted by Cruzr Joe
So, I followed the link and ordered. Just received the faceshield this morning. It is as ordered, BUT...... you still cannot add the visor unless you make alterations to the visor (extend the holes on either end of the visor, so that they are slots rather than holes. I haven’t done this yet, but plan on trying to do it. So, if anyone else is ordering, be forewarned.
Tri-Axis Chrome Handlebars
Sena SM10 BT Dongle
Double USB Port/Volt meter
LaMonster Magic Mirrors
BajaRon Swaybar
HALO Skid Plate
Spyder Pops Rear Running Lights Turn Signals/Brake Light
Spyder Pops Mirror Running Lights/Turn Signals
Shorty Antenna
LaMonster Cat Delete
Akrapovic Muffler
FOBO2 TPMS
Rear Trunk Rack
Bruce Erickson
Chilliwack, BC
Canada
You know when a politician is Lying. It's when his lips are moving!
2014 RTS-SE6 - Cognac
intro to m/c 1949 Royal Enfield 500cc thumper
-
just got the cavalry helmet,the helmet comes with m6-1 female thread nuts molded in the helmet,to replace them you need to find a machine thread snap with that thread pitch,they don't make one.The snap on visor with sun shield so far will not work.The snap are made to fit a standard style snap helmet,meaning the cavalry helmet holes are far wider than a stock one .So this is so far a bust,but will keep looking into this
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|