I have been reading through other threads on drink/cup holders. Most of what I have read is for RT's. Not sure if they work on the F3S. So what are you using for drink holders.
Check out Lamonster Garage on the home page. He has a drink holder for the F3.
2020 F3 Ltd
Spyderpops Bumpskid Spyderpops Brake/Run/Turn Signal LED's
Lamonster Garage LED Fog Lights and Headlights 2013 ST-S retired 1/9/16 at 25,061 miles
2015 F3S sold at 77,565 miles.
I have been reading through other threads on drink/cup holders. Most of what I have read is for RT's. Not sure if they work on the F3S. So what are you using for drink holders.
JOHN;
here are some better pix (i hope).... everything is black, so it can be difficult to see clearly....
i have mine mounted to the RAM MOUNT that holds my GPS... however, a cup holder can be mounted to the bar that my RAM is mounted to...
good luck with your endeavor.... 20180604_095818.jpg20180604_095826.jpg20180604_095856.jpg
i installed the GREEN foam so that smaller bottles wouldn't rattle around while riding....
Dan P
SPYD3R
PS: this cup holder was given to me by the above guy; JKMSPYDER......
i just purchased a 2016 F3L and mounted the Drink2Go holder to the handlebar on the left side as i had it on my 2013 STS. The problem is that the bottle blocks the left mirror completely. LaMonster has a fancy holder that attaches to the frame, just in front of the left knee, but i'm hoping to find something not as expensive.
Originally Posted by SPYD3R
JOHN;
here are some better pix (i hope).... everything is black, so it can be difficult to see clearly....
i have mine mounted to the RAM MOUNT that holds my GPS... however, a cup holder can be mounted to the bar that my RAM is mounted to...
good luck with your endeavor.... 20180604_095818.jpg20180604_095826.jpg20180604_095856.jpg
i installed the GREEN foam so that smaller bottles wouldn't rattle around while riding....
Dan P
SPYD3R
PS: this cup holder was given to me by the above guy; JKMSPYDER......
9 bucks and free shipping. You can use the screws to mount it on behind multi-function housing OR I think you can just clamp it on handlebar of F3. Either way it should work. http://www.providence-spyder-accesso...s/show/7545050
i just purchased a 2016 F3L and mounted the Drink2Go holder to the handlebar on the left side as i had it on my 2013 STS. The problem is that the bottle blocks the left mirror completely. LaMonster has a fancy holder that attaches to the frame, just in front of the left knee, but i'm hoping to find something not as expensive.
Had exactly the same problem, Goldie, with a similar cup holder. Manufacturer stated it was specifically made to fit my 2017 F3L, but when in place (attached to multi-function switch housing), it blocked 60% of my left mirror. I fixed the problem by buying a piece of flat aluminum bar about 1/2" wide, 1/16" thick and about 6" long. Drilled 3 holes in it, bolted the supplied bracket to it and then mounted the extension bar (on the multi switch housing), where the supplied bracket was originally meant to go. This resulted in moving the cup holder about 3" more to the middle, and gave me back a clear and unobstructed view of the rear view mirror again. Cheap fix and I was still able to use the cup holder I had bought, and not waste my money. (You can use the two mounting bolts supplied with original cup holder bracket, but you'll need a small/short 3rd one with a washer & nut at inner end. Took better pics this morning, in daylight.) 20180706_075645.jpg20180706_075627.jpg
Last edited by bushrat; 07-06-2018 at 07:14 AM.
[SIGPIC]
2017 F3 Ltd. Intense Red Pearl/Metallic Black topside
2017 F3Limited , lowered brake pedal Intense Red Pearl w. Metallic Black topside
Had exactly the same problem, Goldie, with a similar cup holder. Manufacturer stated it was specifically made to fit my 2017 F3L, but when in place (attached to multi-function switch housing), it blocked 60% of my left mirror. I fixed the problem by buying a piece of flat aluminum bar about 1/2" wide, 1/16" thick and about 6" long. Drilled 3 holes in it, bolted the supplied bracket to it and then mounted the extension bar (on the multi switch housing), where the supplied bracket was originally meant to go. This resulted in moving the cup holder about 3" more to the middle, and gave me back a clear and unobstructed view of the rear view mirror again. Cheap fix and I was still able to use the cup holder I had bought, and not waste my money. (You can use the two mounting bolts supplied with original cup holder bracket, but you'll need a small/short 3rd one with a washer & nut at inner end. Took better pics this morning, in daylight.) 20180706_075645.jpg20180706_075627.jpg
9 bucks and free shipping. You can use the screws to mount it on behind multi-function housing OR I think you can just clamp it on handlebar of F3. Either way it should work. http://www.providence-spyder-accesso...s/show/7545050
Does this one block the mirror? Hard to tell by the angle of the photo. I had a butler, but the hubby stole it for his new goldwing.