Search:

You can do exactly that with BUDS.

It simplifies wiring. Look at the number of buttons/switches on the left handlebar. I have two paddle switches, Reverse switch, 6 display switches, and turn signals. All those plus a ground, that's...

There is a heat shield on the exhaust manifold left side.

It sounds like you found the cause of a problem that you introduced. Have you found the cause of the problem that you had in the first place?

My post only applies to a very specific case, not shifting in general. By holding the paddle a bit longer when attempting to shift from 1st to N, I was unintentionally invoking a double shift. But,...

The intake plastics are notorious for making a rattle or buzz. Many have added weatherstrip to quiet them. Do a search.

Try searching "2011 Spyder RS" on eBay. If you find a seller for any part, try contacting them to see if they have a cluster. Salvage operators may not post all the parts that they may have available.

I expected to find it under "Body" but did not. I did a search on "position light" to find it.

Service manuals are acessible at powersports-diag.com if you have a login.

Service manuals are also pretty reasonably priced here:
https://brpmanuals.com/product-category/rykers-spyders/

I have a 2014 RSS that I recently bought used. It has standard turn signal bulbs, but the previous owner had installed amber and red LEDs in place of the reflectors on the fenders. Don't know if that...

I changed color on one of my helmets with a rattle can.

I've been riding my 2014 RSS for about a month. When I tried to shift from 1st to Neutral, sometimes nothing would happen. I would have to do it 2 or 3 times to get it to work. I recently came across...

Religiously.

Yes, I screwed up when I said "TCM connector". When you disconnect the solenoid connector, you make the resistance test using the connector end that runs to the solenoids. When you make the test...

I'm a bit confused by this, as the test light is not used for the resistance test. Disconnect the solenoids connector, run the engine, put your test light on pins 8 and 1 at the solenoid connector...

I took my rear wheel to the local tire shop. They said they could mount the tire but not balance because the hole was too small. I got it done at a Can Am dealer, they wanted the brake rotor on to...

I picked up a used Ryker SAS for $70 and a used Spyder yaw rate sensor for $30 on eBay. Both worked fine. I do have BUDS to calibrate them.

Service manuals are cheap and well worth the cost:

https://www.flipbookpublishing.shop/#/

I have both a 2019 Ryker Rally and a 2014 Spyder RSS. For you two, Spyder.

Thanks. I guess the graphic is that of a solenoid. I will check headlight aim. I'm also installing a pair of Denali aux lights.

The service manual wiring diagram has this high beam bulb graphic, but I don't know what it means. The manual text does not address this at all.

How do you access the high beam lamp on the projector headlamp? Low beam is obvious. Low beam is H7; what is the high beam bulb?

I bought a 2014 RSS used. I rode at night for the first time, and...

With those error codes all over the place, it suggests a more systemic problem than a single sensor or module. One more battery check with your multimeter is to measure voltage while cranking.

A...

I recently bought this 2014 RSS with many body parts missing due to a minor crash. Here's how I found parts.

Look up part numbers here: https://epc.brp.com/. Do a search on the part numbers that...

As per my earlier post, there is an electronic switch (probably a MOSFET) in the TCM that makes a ground connection to activate the solenoid. Because this electronic switch has a high impedance path...

The solenoids are activated by current. For the forward shift solenoid, battery voltage is present at Pin 1. Pin 8 is open. To activate the solenoid, the TCM connects Pin 8 to ground to complete the...

So oil pressure is likely fine. Your test results puts the forward shift solenoid in question, or some electrical problem with the forward shift solenoid. I would try to test for voltage to that...

I think you need to use one that will bleed the line. Maybe you can find another. I would start with verifying that the solenoids are working before moving on to suspect low oil pressure.

If you...

I recently bought this 2014 RSS with many body parts missing due to a minor crash. Here's how I found parts.

Look up part numbers here: https://epc.brp.com/. Do a search on the part numbers that...

From what I understand, what you call the "return" line is connected to a valve to bleed the gauge's oil line. Per my maintenance manual, the test is to read the pressure while the clutch is...