Search:

Pretty lame that BRP has this feature. Tiny little blinker indicator on the left side. Give me a break.

Harley has had separate switches for Left and Right indicators for over 2 decades. Self...

2 at the top ... 2 at the bottom.

Moving me back 2-3 inches would suit "my friends" well, but the bars would be too far forward now.

I think the bars are too high now, too ... but, they need to clear the tank.

I guess there is...

Thanx. I tho't it was under there some where. Now I understand about the push pins and where to locate the battery.

Appreciate you response, SPYD3R

Thumbed thru the manual looking for battery location on my F3, but didn't find it. Manual seems to lack an index.

I figure it must be "up front", but looking in there I don't see how that would...

If the Corbin moves one back a bit, that would be nice.

I've noticed with the stock seat that I am nearly "on the tank" when sitting on it. And, this puts some unwanted stress on your you know...

I've only couple hundred miles on the F3S, but the bars are too tall for me and I'm 6'2". And, I've had many bikes. Several I've had to have risers added ... some, I've had a machinist make me some...

Thanx, Pete ... yeah, nothings easy for me and my Harbor Freight tools. But, I got it done. Looks great, feels great, too.

Also, installed the rear grab bar bungee buttons. That went without a...

So ... removed the entire left side foot peg assembly. Put it in a vice and cut thru the "ear piece" of the peg housing near the bolt. Popped the piece off and pushed out the stripped bushing with...

I just spoke to someone here on the phone that had the same/same problem with a bolt being stripped.

He said he had to remove the entire foot peg assembly from the bike and cut thru the peg then...

Well, got the right side of the bike hooked up. A bit of trial and error, but went fine.

But ......... on the left side, heated the front bolt on the peg and it came off (just as the other side)...

That's what I'm looking for !

I'll give that a try.

BTW, I got hold of it pretty well and pushed ... nada.

I'll give your method a try and respond back.

Thanx, man !

If it rains today, I may attempt this project again. Maybe use a dowel to push the brass bushing back out. Seems pretty well seated in there.

Otherwise, I'll get hold of Jacob or Lamont on...

Yeah, I've watched this vid a dozen times ... before and after purchase ... and, twice today.

The brass bushing has 2 "ears" extending beyond the rubber deals. One can't just push with your...

Thank, Pete ... but, unfortunately, the "ears" on the brass bushing are on both ends. I tried to push it out with an allen wrench. No dice. Tried to use a screw driver to remove the rubber...

Got my RIP boards last week. Opened them today, but no instructions.

Went to Lamont's site and he has a vid, but is not thorough enough for a non-wrench such as myself.

Soooo .... if anyone's...

My F4 arrived yesterday ... 9/15/16 ... installed it's just about 1" above the cowl, maybe less.

Riding it up and down my driveway yesterday at 15-20 mph in the lowest position did give me some...

So, after lunch, I removed the seats and installed the Ultimate backrest. A tiny bit of angst in replacing the rider saddle ... seems no one really designs saddles to be easily removed and replaced....

Got home a bit early, so decided to see how hard it would be to install the 28" tinted F4 windscreen.

Read the directions a couple times and dug in. Not too bad. Pretty much straight forward...

I typically wear a yellow helmet on the motorcycles. Both the F6 and the HD have intense highly visible yellow running / fog lights, too. I'm kinda hard to miss .... hopefully.

Plan on riding...

Taste is an individual thing. But, I think this is pretty schweet !

Not sure if it's a PITA. I have a F6B in mat black/silver ... some folks say it's crap paint. But, I just use some Windex like stuff cut 50% with water ... spray it on and wipe down with a micro...

Laminated the temp plate to a piece of cardboard. Then rode up and down the driveway several times, then around the hacienda. Not very loud in my opinion compared to the Stage 3 Harley. I may...

Well .... living in shi**y New England, we have that frozen white stuff that falls from the skies every winter. So, there are 3 snow blowers in front of the F3. And, on the 2 wheeled truck is a...

Andover .... east of Manchester. Near Bolton / Hebron off Rt 85.

Spyder arrived 7:15 AM today. Driver dropped it off, I drove it up the driveway and into the garage.

Here it is.137503

Now, I have to learn how to ride this puppy !

137502

This is exactly the information I was seeking.

Thanks, guys !

I hate to haggle. Just not my nature. Confrontation is not a problem, I just don't like trying to talk someone down in price. I ask for their best price, then see what it is. I re-ask if that is...

You all have been sterling in your responses. I appreciate that.

I must admit, that with just 3 "test rides" of about 10 minutes each, finding the F3-T "twitchy" in my hands, I was (and to a...