Search:

The steel driven plate, while thicker, also has offset tabs on the perimeter, providing clearance for the friction plate tabs as they are also offset as well as being U shaped, while still allowing...

After looking at your chart that you posted, and my limited knowledge concerning your machine, (ie, sm5, turbo charged) I had a couple of questions. The sm5 has a vacuum assist clutch that comes into...

Putting a new nozzle in is a very simple, straight forward procedure. Taking the panels off to gain access to the location will take you twice the time as the actual procedure to replace it.
Not...

Sorry, you are correct. Should have clarified that I was referring to the se5.

The centrifical clutch assembly, without going into much detail, contains several disc's that perform different functions and some centrifical weights referred to as rollers. As the engine RPM's...

These are some photos showing the difference in the steel driven plate, the offset faces the disc pack, very important to soak the plates in oil for 1/2 hour prior to installing. The clutch pack...

The only spring involved with this kit was the spring disc. The pressure plate and clutch drum assembly were not involved, so did not remove them, as my discs had just started slipping and were not...

There is quite a bit of difference in the new and old nozzles. The old nozzle is very short, whereas the new nozzle looks somewhat like the needles that are used to air up a ball. It is considerably...

Thats when I noticed it. Either when I would hit resume on my cruise control or when I would pull out to pass another vehicle and roll the thottle wide open. The RPM's would jump but the Machine...

After putting in the new clutch kit with the extra two plates plus a thicker steel driven plate, and a new disk spring, I assume it just tightened things up a little, made the clutch somewhat more...

Reason I ask, is now when I put it in 1st or reverse, the clutch grabs and at an idle will try to move the machine if it is on the level. Really not a problem, just don't have to have the rpm's up to...

Might I inquire as to what the symptoms were, how you realized it was your clutch. Any unusual sounds, etc. Which way was the clutch shimmed wrong? Too much, or too little. Thanks for your replies.

Removed the clutch cover and remeasured the pressure plate and disk spring, and the distance from the top of the clutch hub to the last friction plate, and found that while I had measured it...

Any reason I could not use the 1mm plate from the original pack? It isn't burned or warped. Also the example given in the manual, would seem to imply that measurement B, is greater then A. This was...

Since it has an additional friction plate and steel plate, would this eliminate the need for using additional adjustment plates. Should also add that the new steel driven plate is thicker then the...

The new clutch for my 09 se5 came in Sat., so installed it yesterday. Soaked the new plates in engine oil over night, took my time and performed everything by the book. took it out for a test run,...

Thanks, looks pretty straight forward.

Thanks Lamont, I only obtained the SE5 number as that was what I ordered. Clutch is supposed to arrive next Tuesday. I'll take some photos and post them on the installation.
Do you know what...

Just finished ordering the new clutch. The part number isn't in the computer yet. They were finally able to obtain it and order same.
If anyone is interested, the part number is 420281935, listed...

Thanks Lamont. Would that entail changing the entire clutch assembly, or just the clutch plates?
If I order the parts from my local Spyder dealer, would I need to specify the new clutch to ensure I...

I don't notice it much in 1st or 2nd, but I can replicate it anytime I want in the upper gears. Especially in 5th. It does seem that it has become much more pronounced since my last oil change when I...

Amsoil motorcycle oil. Got it from Baja Ron. Other oil used was obtained from BRP for the Spyder.

When I roll on the throttle at higher RPMs, the engine revs and the Spyder catches up after a couple of seconds. Assuming I may need a new clutch plates, is anyone aware of after market clutches for...

June, 2003. 09 RS.

I'm thinking about adding handlebar extentions to my 09 GS. The Kewl metal setup look a lot like the ISCI setup. Does anyone know the difference between them and/or experience with them. The cost is...

I'm thinking about adding handlebar extentions to my 09 GS. The Kewl metal setup look a lot like the ISCI setup. Does anyone know the difference between them and/or experience with them. The cost is...

I just had three new tires (G force sport on the front and Toyo proxes 4 on the rear) of my 09 GS. What air pressure are you running? Are the recommended pressures by BRP too low? I'm presently...

Ray, I changed my #1 switch to off, changing my gain to medium. That eliminated the surging completely. But when engaging the cruise control at any speed, it would immediately accelerate 3 or 4 mph...

Ray, thanks for the pictures. Finally got it installed. What switch settings did you use. When I set my cruise, I need to let my speed drop about 5 mph before the control engages. Is this normal? ...

Ray, thanks for your response. I made a custom cable loop and popped the plastic arm off and put the loop there. The original loop was too long.
What I was inquiring about was where and how you...