Search:

VSS pressure switch dhows brakes are on full all the time .

VVM sensor failure estimate $2,000.00

For sale

Well I appreciate all your help, I found a dealer that will take it in sooner. I hope that what they find will help someone else .

I'm down with the same thing did you resolve it ? Any advice?

I'm fearing your all out of ideas ;-(

I found this post "Question on Codes P061E and P0504" which explained a lot if it was the problem. He never says

Well I found some small rocks under the boot that holds the brake switch. The last thing I did was drive up my washed out dirt driveway. I don't see any damage, its not easy to get to see anything. ...

Before I report , thank you for all the help on this nightmare.

So All I have done is check brake fluid, check fuses, disconnect the battery for an hour or so, check and inspect brake switches. ...

codes C0044 C006C

The switch is there, there are two wires coming out of the box but there is only one switch that I can see. It clicks when you press the pedal down and clicks again when it's released. But if there...

I can only see one switch, it clicks twice if you count the return of the peddle. Now that the battery is reconnected it will only idle, the throttle is dead. Things are getting worse.

The fluid is the original, It has a bit of color to it. I though of flushing it out but from other posts it did not seem to help

Fluid is up

Hum, I only hear one click

Hi thanks , it's a 2012 the manual is the same for 2011 and 2012

2012 spyder RT

I hope someone can help me.

I parked my bike in the shop and it was very humid for a few days. When I went to start it, it came up with an ABS failure. When I drove it out...

Thank you Pete

The switch works properly to the brake light, is there something I'm missing? the C0044 code says a blown fuse to the brake light and or the ABS pressure switch which is my next challenge to even...

Hi, No modifications, the only thing that happened was a rougher ride down my washed out driveway on my last ride. I did the pump hold stuff , no luck. I looked and looked for any damage and can't...

Hi , The brake light works as it is supposed to. The code says it's a brake pressure sensor on the ABS normally caused by low fluid.

Yes , That is just if I want an oil change and the B.U.D.S. put on so I get more codes. They are selling way more then they can service. It has made me re-think the purchase.

Help! I parked my bike for a few days and now I get an ABS failure and it goes into limp home mode.

The brake fluid is topped off , the floats are mobile. Battery is up, the fuses are good to the...

OK I'm new to this site and for the life of me I can not figure out how to start a new post. I have a C0044 code and limp home mode and my dealer can take the bike until the end of August Help

OK, Here's the result, First thanks again to all, and the videos on this link and can am TV for great insight as to how to get into the machine.

Evidently this was not the factory battery. The...

Yes I had only cleaned the visible leads , now that the panel is off, I can't believe how dirty it is in there. Any ideas on the best way to clean it out? Air is not doing that great a job. Pressure...

I checked all the fuses, good I took the visible terminals off cleaned with a tooth brush and electric clean. I hit the horn accidently and there was a very faint click. I hooked up my Shop jumper...

Going fuse hunting - I'll let you all know , thanks for the fast reply's!

I have not checked that I was thinking there was a fuseable link somewhere in the line

It is the original battery, it tested good, there is power to the leads (metered) and I rode it 10 miles just prior to this problem

Help ! the sun is out and I took a short test ride, came home and packed for the day. got on and turned the key and noting happens at all. No lights, no noise, no nothing. Battery has been on charge...