Well the consensus seems to be the Yuasa factory filled, that would be the non-BS one correct?
Steve
Type: Posts; User: Troublemaker1
Well the consensus seems to be the Yuasa factory filled, that would be the non-BS one correct?
Steve
Guy's it's time to replace the battery on the 2010 RT, I watched the replacement videos, some great, some not so much but all helpful. but the big question is what the best economical battery for the...
Hey Guy's the 2010 RT has developed another rattle the last one was the muffler which Lou replaced (Yea! Lou) this ones in the Cat is there anyone out there that removed theirs to put in the bypass? ...
No worries Mate,
Your directions were fine, the problem came when the mark on the gear turned out to be gone. and me trying to figure out top. the wedges worked great. the gear was kind of...
Hey guy's thanks for all the know how on how to do the change. got it done about three weeks ago and fixed all my mistakes last week end. apparently you can put it on backwards even with the marks on...
Doc Riverside?
Hey guy's did anyone get all the installation instructions? Several pages didn't down load including 19. before I cut or drill the wife's Spyder I need to be sure.
Steve
Hey Guy's did anyone do a video of removing the Tupperware around the windshield base? there is at least one or two on re-placing the arm but they all start with the TW removed.
Steve
Will the windshield fit a 2010 RT?
Steve
Powersports warehouse.com
Can-Am - RT VENT KIT
Item: 219800388
I'd like to order and install these on our 2010, can we buy them yet? The wife has gone through 3 right boots due to the heat melting the glue and allowing the soles to separate. To bad I'll have to...
Actually Cena did but I'm not supposed to mention that.
I'll take a couple of good pictures tomorrow, the one on the post is just to show what piece I was talking about. right now the marvels of duct tape are holding it together.
http://www.spyderlovers.com/forums/attachment.php?attachmentid=105429&stc=1Hey guys, had a small mishap with the 2010 RT this weekend, seems it drove over a four inch curb and crunched the dull black...
In that case lunch and a bed for an over night is on me. provided you don't mind cats.
Steve
Sounds good how far is home from Chula Vista? and what do you want for lunch...
Hey Bob,
On page one of this post someone mentioned changing out the stock alum cover with a colored one and you mentioned it was quite a bit easier,
Did you do a video on that?
Steve
Hey Guy's does anyone have a link to the U-tube video on istalling the baker built air wings? I watched the other day and didn't save it and nacth can't find it again.
Steve
I see this thread has been up awhile, what's this thing cost and is it available in the states yet? is there a web site to look at the instructions? I've seen the Utube video and like the concept.
I remade the wires that are part of the plastic round parts, they seemed to be the weak links. you can attach a landyard to the mirror and body as well. it will catch the mirror should the "cheesy"...
Hey folks,
Who's a good supplier for the short gas shock that holds up our trunk lids? I know there will be several of you that want to say Can-Am and yes I can go that route, but I’m sure as long...
Would i need two sets to run the two strips or just one?
Troublemaker1
Lou at Pirate motorsports took care of it. great job Lou thanks.
Looking for a stock 2010 rt muffler, something broke loose in ours. Anyone got one laying around after an exhuast change?
OK I give up, did we ever figure out if us Ca guy's could get this panel?
Steve
John,
Is there a step by step for installing the Elka rear shock on an Rt out there?
Steve
cenaub4@att.net
http://www.spyderlovers.com/forums/showthread.php?54599-Farkle-2-RT-Trunk-Break-light-DIY-full-video-how-to&p=687483#post687483
this same thread, StanPoff about half way up the page.
...
Bob I picked up the lights yesterday and will do the mod this weekend, if i can convince the primary rider to stay parked long enough. even with out the light part I now know how to take off those...
Guy's you mentioned the ELKAs has anyone run the progressives?