Search:

I have a 2013 RT Limited seat that I need to get out of my way - honestly you pay shipping and it is yours.

While riding in NC in October we noticed that the rear end felt loose so we stopped. After diagnosing it we felt that the rear wheel bearing was out of it. We towed it, now we were in Highlands NC...

Removing it is pretty easy. You will want to raise the windshield up to the point where you can get to the bolts/screws on the backside of the windshield, remove one each side. On our 2013 Limited...

check out spotwalla.com and if you have an android device bubbler gps, there is an equivalent for IOS.

If you do not want to use your phone, SPOT is the most commonly used one in the LD world.
...

We have a 2013 RT - I have noticed when it is hot it will cut out or skip if you will. We just returned from a 4 day 1500 mile trip and it acted up only when it was 85+ for a few minutes and then...

You didn't specify front or read, however we have the following on our 2013 RT: http://www.spyderflap.com/products.html they are a sponsor of the site.

On our 2013, I used a furniture moving dolly from Harbor Freight, it is about 1/4 to 1/2 higher than needed so when the frunk was loose, I lifted up on the front, slide the dolly under and the frunk...

There is a cable that is attached to each headlight unit with an end that is attached to the "frame" under each small panel that covers the radiator on the right and oil on the left (this is on a...

Joe thanks, I went to a store called Ace Hardware and they had one, the pitch is 1.5 and the size is M14.

documenting for future;

The nut is a M14 pitch 1.5, the one from Ace Hardware is a little thicker but it seems to work.

I have found that to be true more times than not and has recently become my first place to go.

It is the nut that holds the adjustment cable to the frame and has to be removed in order to remove the headlights.

I had taken the front end apart and misplaced one of the adjustment cable nuts, I am sure it is in the garage somewhere but at the moment cannot find it. I have searched around and cannot find it...

We have pulled our trailer fully loaded all over Eastern USA including a SS1000 in May of this year and have never noticed it back there except for backing up.

I saw these on the edges of the headlight assemblies, I do not know if they are also on the fog lights as well.

We use a coupler lock similar to this: https://www.amazon.com/Reese-Towpower-72783-Universal-Coupler/dp/B0008FUH46/ref=sr_1_4?s=automotive&ie=UTF8&qid=1502131517&sr=1-4&keywords=trailer+lock as well...

2013 RT Limited - approaching 24K miles and feels stronger today than it did 5K ago. When we bought it I planned to drive it until it falls apart or I determine it is a risk to drive, at 19K we took...

I use the suction cup on the frunk - I built a tether that I loop back to the top of the dash, now that I picked up the bar from JT it will connect easily there, if the suction cup ever fails it...

I have a 2013 RT Limited and after 14000+ miles I confirmed that going 70 and under will increase the MPG as well as lowering the rear shock will allow you to fill the tank giving more mileage, I...

We have had our Corbin seat on our 2013 RT Limited for over 13K miles now. I also had a Corbin seat on my Honda Shadow therefore I was already familiar with them. If you are familiar at all with...

I use the suction mount on the frunk. I built a tether that loops under the mirror and connects to an eyelet item I attached to the bolt on top of the dash. After a few rides I decided to paint it...

This last tank I had 32.5 which is using low octane

Sent from my HTC6535LVW using Tapatalk

Prior to the recall I was avg about 25, after the recall the tanks have been 29 - 33. Before I never felt I could make 150 miles per tank, the reserve light would come on somewhere between 110 and...

How the linkage fell off is unknown, I was not able to put it back on without taking the screw out. What I didn't know the first time was that you needed to pull the linkage so that the arm would be...

Given that the shift linkage came off, how would one shift it into Neutral before reattaching the shift linkage?

Well I opened the garage up and looked under and sure enough, a shift level is hanging there. I found the spindle and at least the teeth on it feel good, nothing obvious by feel ground up or smooth,...

Was riding home Tuesday and went to downshift due to slowing traffic and the Spyder sounded like it tried to downshift and then surged but the indicator would stay at 4.

Oil changed in late...

I live in Florence KY and drive to Lexington Motor Sports for my service, not a lot of choices in Northern KY for Can-Am dealers. Of the various dealers I have dealt with, I have found them to be on...

Try http://johnnykspowersports.com/, they helped me locate a 2013 trailer in April of 2014 and they actually pulled the trailer from a dealer in PA. They may not be able to help but it is worth a...

I called LMS to schedule the recall work, the person I talked to was not a technical person, however she stated that the tech is planning on 1.5 days per spyder to do this recall. I guessed at a day...