Search:

Ok, I've found that the bulb in question is a BAU15 based bulb P21W style with 30 deg off set pins on the PA6 base. Not a standard North America based bulb or base as it is made in Italy for the...

Update.. Well I've completed my winter project... Mod's are: Rotopax mount on front, 1 gallon fuel, and 1 gallon water; Cooler rack with MooseJaw cooler on rear.

207445

Thinking of fabricating a rear class 1 or 2, 1.25 hitch reciever to bolt on the rear of the RT622 trailer for temporary use of a small cooler. I carry a lot of camping gear when we go camping, so...

nice, was thinking of doing the same thing. I was going to mount a cooler and these on each side of the cooler. Then I realized these two fit nicely inside the trailer at the back right behind the...

The back lid gas struts have reduced their pressure to hold it up (drops about halfway). The gas strut part is SUSPA C16-27966. SUSPA doesn't give out specifications i.e. gas pressure or lift. ...

I have a RT622 and my wife and I are planning on doing a long-distance ride that will involve mostly camping. The trailer cargo capacity says 150 lbs. I find that little low considering the amount...

Thanks, didn't think of that...
:bowdown:

Anyone know of an easy way to adjust the front lid on a rt622? Previous owner had the removed the lids to paint the trailer. sort of got them back on but huge gap was between front and rear lid. ...

ok, the update on this.. the e-trailer ST145/12 tire performed outstanding on a recent 1000 mile trip. Tire pressure reading on the tire was 65 psi max cold tire pressure, since the radial was...

Anyone know of a good Yellow LED replacement for the 706W yellow bayonet single pole bulb?191503

yep installed mine today. used step bit to make center hole larger. Used dremel tool to elongate the holes in then light assy from etrailer. makes trailer look better. like @fatboy..

Follow up. Well, don't.. The axle may work, the tire probably won't. I replaced my 4.80 x 12 tire with a ST145/R12 high speed radial from E-Trailer. Excellent tire, but here is what I had to do....

191083

specifically UltraTow #57225 high speed hub 5 bolt on 4.50 spacing with L44640 inner and outer bearings and comes with 1.25 and 1.50 seals. More options on wheels and tires over 4 bolt.

Anyone upgraded the hubs to a 5 bolt 4 1/2 bolt pattern and upgraded to a 13" wheels?

191070

Just wondering..

I was thinking about using something like this to the bottom mount bolts in my 622 trailer. 190874

Anyone have the specifications of the height of the 1-7/8 ball (top) from the ground
(floor) for a RT hitch? Just wondering what the normal height is supposed to be to pull the RT622 trailer...

I used a dremel tool with small grinding wheel to cut notches in the hub on 4 sides just enough to gain the edge on the bearing races on both sides of the hub. Future bearing race changes won't be a...

never mind.. got my answer on another post.

i notice the holes for mounting is not the same.. did you have to drill new holes?..

Great job... looks good.. I'm sort of wanting to modify this some.. I have a Goldwing with Rivco hitch pulling the 622. Goldstrike makes a fender extension but I do not want to add to the bike. ...

spyderpops shows not available.. only wish list item..
190685

I noticed in the parts breakdown that the lid seal is listed as part 77 on both lids. can anyone tell me if this sku has enough for both lids .. or will i need to order two of them.

Neoprene...

Anyone know if you can purchase just the mud flap? 190669

Ok, I’ve had to do a redo… the trailer had a 6 pin wiring from the factory. The signal and brake light were originally wired separate .. a later mod was apparently installed (just the fwd harness,...

On the RT622 trailer, 2010 model, the previous owner had a 4 pin square connector (OEM) that was installed. Converting to a 5 pin flat, and using the pathfinder isolator hub, I can not get brake...

I'm a proud owner of a new 2 me, 2010 RT-622 Roadster trailer. I love the look and features of this trailer. Have some new bee questions.

I've been browsing some of the other post here and see...