Search:

Type: Posts; User: Trapdoor

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    6
    Views
    3,267

    In my case, the P0340 fault did not affect the...

    In my case, the P0340 fault did not affect the engine rpm or 70 MPH speed while driving on the freeway. So I drove the spyder to the dealer and had it replaced. Third party extended warranty paid for...
  2. Replies
    17
    Views
    5,761

    P0562 - System Voltage Low. Steps you can do is...

    P0562 - System Voltage Low. Steps you can do is to check for blown fuse, load test the battery, check voltage output of voltage regulator (13 - 14.7 volts), check connection on the voltage regulator,...
  3. Replies
    6
    Views
    1,462

    Had the same problem with my 2017 F3S-SE6 at...

    Had the same problem with my 2017 F3S-SE6 at 7,097 miles. Bike parked in the garage for one week waiting for my appointment with the dealer. Two days before my appointment, I took the bike for a run...
  4. Replies
    37
    Views
    38,338

    Sticky: HowTo: Android phone and Windows 10 users: My procedure...

    Android phone and Windows 10 users: My procedure is to import the picture into the computer. Then I make a copy of the picture in case I "oops". Next, I right click on the picture and select "edit",...
  5. Replies
    20
    Views
    5,939

    When this no-start problem happened to me during...

    When this no-start problem happened to me during my 2-wheel riding days, it was always corrosion on the battery terminals and corrosion on the chassis ground point. Next time it happens, I plan to...
  6. Thread: RAM X-Grip

    by Trapdoor
    Replies
    11
    Views
    1,927

    RAM X-Grip

    I use the X-Grip to hold my smartphone even though the side-to-side movement irritated me. So I found a product at Home Depot that would dampen the side-to-side movement - Velcro coin #90362, black,...
  7. Replies
    3
    Views
    1,215

    I measured the diameter of both sway bars. For...

    I measured the diameter of both sway bars. For the OEM version, it is 14mm; Baja Ron's is 16mm.
  8. Replies
    9
    Views
    11,227

    The Baja Ron instructions said to remove them....

    The Baja Ron instructions said to remove them. Once removed I had planned to clean them up and paint them, which I did. I agree with you on "lifting the spyder high enough". The two pics are my...
  9. Replies
    9
    Views
    11,227

    I found out what I did wrong after looking at the...

    I found out what I did wrong after looking at the parts list - I missed removing one torx screw. This screw was hidden from view because it was not visible like the other three torx screws unless I...
  10. Replies
    9
    Views
    11,227

    Push pin removed and I was able to slide it aft...

    Push pin removed and I was able to slide it aft and rotate it out of the way. Still not able to separate the deflector part from the shell part of the clam shell assembly.
  11. Replies
    9
    Views
    11,227

    Deflector Removal Problem

    I ran into a problem while installing the Baja Ron sway bar on my 2017 F3S. I removed the torx and phillips screws on the two "clam shell assemblies" but they won't come apart. Something else is...
  12. Very cool lights! Where can I get one?

    Very cool lights! Where can I get one?
  13. Replies
    122
    Views
    30,793

    Same here. I usually refuel when the gas gauge...

    Same here. I usually refuel when the gas gauge indicates 1/4 full. I alternate between mid grade or premium, if I can remember what I put in the last time.
  14. Replies
    4
    Views
    1,735

    HowTo: I just recently removed and reinstalled my rear...

    I just recently removed and reinstalled my rear fender. The first step is to remove the license plate to access the electrical plug cover. Disconnect the electrical plug and separate the cable from...
  15. Replies
    4
    Views
    1,244

    M10 Torque Spec.?

    Please, I need to know what the torque specification is for the Allen bolts that secure the rear fender support. I have a 2017 F3S-SE that I took the rear fender apart for a wash, wax and paint job....
  16. Replies
    7
    Views
    1,729

    Which LEDGlow light kit are you trying to...

    Which LEDGlow light kit are you trying to install? How many hookup wires are on the light kit and how many light strips? I'm assuming the light kit has three wires (one for ground, one for 12V pos,...
  17. A very good suggestion. Another way BRP can fix...

    A very good suggestion. Another way BRP can fix this issue is to have their dealerships focus on servicing the Spyders yet allow them to sell Spyders based on demands.
  18. Replies
    2
    Views
    1,080

    WTB: Are you looking for the old version or the newer...

    Are you looking for the old version or the newer IPS version? I have the old version that I purchased in 07/2017 for my 2017 F3-S. I used it for about two weeks before I took them off the Spyder. PM...
  19. Replies
    13
    Views
    2,473

    Thanks SpyderAnn01 for the info on how to check...

    Thanks SpyderAnn01 for the info on how to check for codes. I tried it and it displayed "No Active Fault Code" on my 2017 F3S.
  20. Replies
    8
    Views
    2,089

    I compared the installation instructions between...

    I compared the installation instructions between the 412 kit and the 431 kit. The 431 kit includes a torque specification chart for bolts, no part number for the idler pulley only, and comes with two...
  21. Did you determine if the right signal lamp socket...

    Did you determine if the right signal lamp socket was not getting +12 volts to it or the lamp socket wasn't grounded properly?
  22. Battery connections may be tight but corrosion...

    Battery connections may be tight but corrosion between the posts and clamps will create problems. And, speaking from my two-wheel experience, don't forget the negative cable connection to the Spyder...
  23. Replies
    8
    Views
    2,215

    I bought the AdMore SMT Light Bar (Small) for my...

    I bought the AdMore SMT Light Bar (Small) for my 2017 F3S but was NOT able to use it. The light bar is a 6-wire connection setup that was NOT compatible with the F3S 3-wire setup. The F3S 3-wire...
  24. Replies
    0
    Views
    788

    LED Light Strip on F3 Rack

    I just installed an auxiliary taillight on my MBL F3 rack. Took me a while due to electrical and mounting issues that I had to resolve before the actual installation. The electrical issues I had were...
  25. Thread: Luggage Rack

    by Trapdoor
    Replies
    12
    Views
    3,921

    Yes! The rack I installed on my F3S is MBL...

    Yes! The rack I installed on my F3S is MBL Innovations' newly designed F3 Rack.
  26. Replies
    6
    Views
    1,417

    Chupaca, I apologize for not including the pics...

    Chupaca, I apologize for not including the pics to illustrate the issue with attachments. The pixel size for the pic that's not right side up is 3024 x 4032; the pic that is right side up was resized...
  27. Replies
    6
    Views
    1,417

    Attaching Pictures

    My first try at attaching pictures to a new thread never turned right side up :gaah:. Drove me nuts for almost an hour trying to figure out how to solve this problem. Finally clicked on the question...
  28. Replies
    1
    Views
    1,382

    F3 Luggage Rack

    My F3S has the BRP detachable passenger backrest and the Shad saddlebags already installed on it. I wanted to add the new F3 luggage rack from MBL Innovations but the instructions did not apply to...
  29. Replies
    6
    Views
    2,338

    I'm planning on buying Lamonster's F3 Fender...

    I'm planning on buying Lamonster's F3 Fender Light Kit after watching the video. The video didn't show how to remove the OEM reflectors which I believe to be step #1 of the installation. Would...
  30. Oops! Meant to say license plate frame.:pray:

    Oops! Meant to say license plate frame.:pray:
Results 1 to 30 of 36
Page 1 of 2 1 2