Printable View
Anyone know how to/ where you can acess wiring and terminations for this lamp?
It doesn't seem to flicker when you just first turn the key on or at idle just before shutting off. :dontknow:
While out riding last night it was out/flickering the majority of the time, but was on steady just before I turned the Spyder off at home.
Check your coolant level. If it's low, the light might flicker. I don't know this on a Spyder but it's true on cars.
:agree:
Ray - the instrument cluster is fed via a single 24 pin wire harness connector. All those indicator lamps are LEDs hard soldered to a circuit board. So, it's not like there are individual lamps and wires anymore. You'll want to focus on why the light was lit in the first place. Did you happen to cross check it with the temperature gauge to see if there was an actual high coolant temperature? As the others have said- check your coolant level and check your radiators for bugs. Appears to be telling you that there was an actual high temperature condition since it came on solid when you slowed down and stopped at home.Quote:
Originally Posted by teninospyder
Thanks, but just to be clear, the light I am talking about is the "backlighting of the gage", just like the Fuel gage has, not a warning type light. I will check coolant, but it was OK a few weeks ago and no leaks on ground, etc. and the needle for temp is in center of range - right now.Quote:
Originally Posted by Snowbelt Spyder
Oh. Sorry. Clearly we all thought you were referring to the warning indicator light. I've never pulled the display assembly myself. But plenty of folks on here have when they removed those analog gauges. Somebody will be able to tell you what's back in there and give you some more help. Stay safe.
Ahhh... that threw me for a loop too...Quote:
Originally Posted by teninospyder
So, if you remove the 4 screws from the instrument cluster bezel, the bezel will be loose enough to pop out. You may have to turn you handlebars to the left or right to get the bezel fully disengaged.
You will only have so much room to work with as there are wires going to the gauges. This wires can be gently pried off with a flat screwdriver or spudging tool. There will be 3 wires on one connection and one stand alone. Both sides are the same.
The back of the two meters will look like this although they will not have to be removed from the bezel.
As you can see in the pictures, the light bulb will be mounted in a little black holder that twists into place. Simply twist and remove, Change the bulb and remount the holder. After you get the wires back onto the gauges, test to make sure they work and remount the bezel to the dash.
All in all it's a 10-15 minute job.
Tim
Ray, go to the Picture 10 - Electrical System Front View after drilling down at this link: https://can-am.brp.com/on-road/us/en...ts-iframe.html. Look for Item 334, PN 219800181, LED Bulb, $3.09. Be certain the bulb is tightly connected. If it is and still flickers, three bucks is a cheap new bulb. If a new bulb flickers you've a faulty connection or possible short to ground back up the harness somewhere.
JayBros, got to the bulb yesterday and pulled it out, looked at it (actually nothing to see for an LED bulb), took connectors off, pushed all back on and installed same bulb.Quote:
Originally Posted by JayBros
Seemed to be working fine, until last night on a ride, after an hour or so, it stopped again and then flickered on and off periodically until we got home. I don't understand LED bulbs so I'm asking if this would indicate a bad bulb, versus a wiring issue?
Going to see if my dealer has a bulb today and will get one, and hope it's NOT a wiring issue :dontknow:
Any comment?
One of my led bulbs that I had put in the fender tip lights started flickering last month. Failing bulb. Replaced. No issues since.
Not an expert on this, but my experience with LED's are they work or don't work sooooooooooooo my money is on loose or temp. ground issue .... ie. - wiring .... good luck .... Mike :thumbup:Quote:
Originally Posted by teninospyder
Ray, electrics are not my strong suit but I would agree with Mike if a new bulb flickers there is a short to ground somewhere.
LED's can get temper mental . Some will flicker and may need a load resister. Now not sure if you have a good 12 volt source. Bulb issues or if there is a resister involved on the Spyders.
Its like my RPM light on my dash its either on or its off.
Got a new bulb coming mid-week from dealer. I'll know then. Hope it's not the ground as I have no idea how to get to THAT point.:banghead:Quote:
Originally Posted by JayBros
OK, got new bulb in finally and NO ISSUES on flickering since.:yes:
comment: noticed when I "studied" the old one, a hairline crack in the white (porcelain?) portion of the body assembly.:ohyea:
Just noting for others, so you don't at first glance think the bulb isn't bad and go searching for a short somewhere. :banghead::banghead: :roflblack:
Ride safe :thumbup:
Glad you got the problem fixed.