Rust-Oleum makes a High Heat paint spray that's good up to 1200 degrees .
I doubt oil temp ever rises above 400 degrees unless a major problem appears.
Would the oil act as a detergent & remove the dipstick High Heat paint?
Darrell
Rust-Oleum makes a High Heat paint spray that's good up to 1200 degrees .
I doubt oil temp ever rises above 400 degrees unless a major problem appears.
Would the oil act as a detergent & remove the dipstick High Heat paint?
Darrell
But there are other options....some have drilled holes some have knotched the sides some have filed hash marks on them. Question is what color though that is not the issue. Its the shinnyness that keeps us from seeing the oil. Especially the newer cleaner oil which in such small amounts is transparent. Has to be a matte finish. Or use the paper method.:thumbup:
would not put paint on the dip stick, it would be gone in a week or so
if your oil ever got to 400 you already have serious problems-more likely 275 would be a max and I doubt you'll see that on a water cooled engine as in our application
the hash mark carving seems to be a good idea
In just one week I have read a thread or know of at least four oil leak issues from overfilled motors. My brand new over filled F3L blew oil out the dip stick the first time I hit 6,500 rpm. Very depressing to say the least. I feel the dip stick would be to fragile/ skinny to drill holes in and might beak off going through the curved elbow at the base.
I think Can-Am needs a service bulletin and an upgrade solution. This is serious stuff as my oil went directly on my exhaust pipe and was seriously smoking when I pulled over. One truck stopped to offer help and asked if my bike was on fire.
new aftermarket product for us sight impaired people. we have vendors here
with the capability. just remains to be seen how many would sell. put an
ips cap on it lamont?
:popcorn:
Don't do it... nojoke
Just place the dipstick on a clean piece of paper towel, and the oil level will be VERY easy ti see! :thumbup:
Easy-Peasey! :D
I think that we should all agree that the directions in the owner's manual must be followed exactly as written... :thumbup:
Owners manual well who needs it anyway:joke::joke::joke::joke:
Sometimes it is written in a confusing manner but we'll all figure it out. I wouldn't go against my car/truck owners manual or my guns,computer,phone,washing machine, ect. manuals. There is a reason for checking the oil the way they do.( semi- dry sump, evacuation pumps, oil holding tank, even oil expansion with temp.)
I did file hash marks on the dip stick BUT I use a paper towel to get an easy reading of the oil level. ( Not that I've EVER had to add oil between oil changes)
Good luck , Kaos
... about using a paper towel to check the oil level. Sure is easier than getting out a flashlight, or trying to feel the oil level, or just guessing... just pulled the stick and laid it on the towel with a little roll...good tip.
Hmmm, I think where the stick is wet, that means there was oil to that level....maybe I'm crazy...LOL...I didn't realize this was even a problem..?:popcorn:
Do it howerver you choose. Here's what Steve from BRPCare said in Oct 2014.
http://www.spyderlovers.com/forums/showthread.php?73737-Proper-Oil-Level-Verification-Procedure-on-1330-engined-Spyders&highlight=level+verification
When I read the dip stick with my eyes and a good flashlight I was not at all certain just where it was reading. Same colored oil and stick?
Then when I tried Bob's suggestion with the paper towel, I realized I was seeing the open eye reading wrong. Each time I tested with the paper towel the reading was the same. Each time I looked at the stick, I was not sure and was wrong if the paper towel was correct. I'm going with the paper towel as it seems consistent.
No, absolutely not. Once the scavange pumps have done their work and have gotten the oil pmped back into the tank -- where the dipstick is actually measuring the oil level -- when the engine is shut off some of the oil will begin to flow back into the dry sump. That's why BRP says to read the dipstick within two minutes of turning off the engine. Left to sit overnight and read the following morning, the dipstick will read low. If one interprets the level to be correct and tops off the oil one may be overfilling the engine. All one is reading in the morning in a cold engine is the amount of oil remaining in the tank, not in the entire engine.
I use a big snap tie, it is about 3/8" wide and I cut it to length and painted it flat black. When I check the oil I wipe it clean and get a good reading. Using it for three years.
Has anyone used sandpaper or scotchbright to dull the finish on the dipstick? It's possible that it would help reading it but Bob is right. You are going to need a paper towel to wipe it off anyway.
Anyone using colored shop towels to read the oil level? Might be easier to see also.
http://www.homedepot.com/catalog/pro...5554d0_145.jpg
Nope, use a paper towel, works great.
On an engine that is up to operating temperatures: Remove dipstick, wipe, dip in cold water, wipe, reinsert, remove and read. The oil will stick to the cold dipstick and it will be real easy to read. Works especially well when the oil is fresh and typically hard to read.
All very good ways to check the engine oil level. Go by the manual and use a clean paper towel. Always had very good oil level checks. Merry Christmas to All Spyder Lovers/Riders. :yes::yes::yes: Little Blue
Black permanent marker on the dip stick I did it two oil changes ago and it never came off.