More farkelitis!

[lou49]

My spider decal! Don't like that brp decal!
Powder coated pipe shield!
Ceramic coated pipe!
Lamonster N B V brackets!
Widow pegs from eBay $50 for a pair!
Front fender rear l e d light!
Custom dynamics upper brake and running light!
Home build l e d 3rd brake and running light!
More to come!:shemademe_smilie:
http://www.spyderlovers.com/forums/attachment.php?attachmentid=126348&stc=1http://www.spyderlovers.com/forums/attachment.php?attachmentid=126349&stc=1http://www.spyderlovers.com/forums/attachment.php?attachmentid=126350&stc=1http://www.spyderlovers.com/forums/attachment.php?attachmentid=126351&stc=1http://www.spyderlovers.com/forums/attachment.php?attachmentid=126352&stc=1

[BLUEKNIGHT911]

Nice :thumbup::thumbup::thumbup:........I see you have the LED strip in the trunk separation.....Mine wasn't as visible as I wan't it to be. So I knew the trunk had an upper and lower part.....the lower part ( inside ) is what seals the dust and moisture out.....I didn't want to trim the upper part......how I got more visibility was to put 3 - 3/16th" thick washers I cut from some plastic tubing I had. I put them between the upper and lower sections on the 3 screws closest to the rear edge........This made the space larger and the LED's more visible, and the trunk still has a tight seal .......Mike :bbq:

[ARtraveler]

Very nice. :2thumbs:

[Ron2andia]

:thumbup::thumbup::thumbup::thumbup::yes:

[Bob Denman]

:D So... What's next??

Farkleosis cannot be stopped, and...


http://www.spyderlovers.com/forums/attachment.php?attachmentid=126360&stc=1

[SPECTACUALR SPIDERMAN]

:D So... What's next??

Farkleosis cannot be stopped, and...


http://www.spyderlovers.com/forums/attachment.php?attachmentid=126360&stc=1

But picard is no longer a borg, he evolved into professor x

[lou49]

Nice :thumbup::thumbup::thumbup:........I see you have the LED strip in the trunk separation.....Mine wasn't as visible as I wan't it to be. So I knew the trunk had an upper and lower part.....the lower part ( inside ) is what seals the dust and moisture out.....I didn't want to trim the upper part......how I got more visibility was to put 3 - 3/16th" thick washers I cut from some plastic tubing I had. I put them between the upper and lower sections on the 3 screws closest to the rear edge........This made the space larger and the LED's more visible, and the trunk still has a tight seal .......Mike :bbq:
Hmmm! I guess I'm gonna have to keep an eye on that! The 3 screws that you are taking about, are those the ones on the lower panels? Thanks Blueknight!

[lou49]

:D So... What's next??

Farkleosis cannot be stopped, and...


http://www.spyderlovers.com/forums/attachment.php?attachmentid=126360&stc=1
UTOPIA BACKREST, GROUND EFFECT LIGHTS!

[Chupaca]

Very nice and a good start. :2thumbs: now take a break and take a few rydes to enjoy all your work and then it will be time to continue.....:gaah:

[BLUEKNIGHT911]

Hmmm! I guess I'm gonna have to keep an eye on that! The 3 screws that you are taking about, are those the ones on the lower panels? Thanks Blueknight!
No .. If you open the trunk....look at the inside upper panel....the one with the Hinges....there are six screws....if you take them out, the panel with the hinges stays attached ......The outside panel ( the painted one ) will just come off ......put that aside....now close the lid.....see those three holes in the front.....that's where the spacers/washers should go ( I glued mine after I figured out how thick they should be - it makes it easier to re-assemble )......after putting in the spacers .....re-attach with the screws......the trunk will still be water-tight as before - because the inside LID has the seal........I think this explanation makes more sense.......It's too bad no-body reads any other posts but the OP's.........Mike :bbq:

[Bob Denman]

UTOPIA BACKREST, GROUND EFFECT LIGHTS!

:clap: Now, THAT's the spirit!! :2thumbs:

[STELLING MAN]

LOOKING GOOD..

[lou49]

Nice :thumbup::thumbup::thumbup:........I see you have the LED strip in the trunk separation.....Mine wasn't as visible as I wan't it to be. So I knew the trunk had an upper and lower part.....the lower part ( inside ) is what seals the dust and moisture out.....I didn't want to trim the upper part......how I got more visibility was to put 3 - 3/16th" thick washers I cut from some plastic tubing I had. I put them between the upper and lower sections on the 3 screws closest to the rear edge........This made the space larger and the LED's more visible, and the trunk still has a tight seal .......Mike :bbq:
Got it! Thanks!

[lou49]

No .. If you open the trunk....look at the inside upper panel....the one with the Hinges....there are six screws....if you take them out, the panel with the hinges stays attached ......The outside panel ( the painted one ) will just come off ......put that aside....now close the lid.....see those three holes in the front.....that's where the spacers/washers should go ( I glued mine after I figured out how thick they should be - it makes it easier to re-assemble )......after putting in the spacers .....re-attach with the screws......the trunk will still be water-tight as before - because the inside LID has the seal........I think this explanation makes more sense.......It's too bad no-body reads any other posts but the OP's.........Mike :bbq: Yes, it is! Thanks!

[lou49]

Very nice and a good start. :2thumbs: now take a break and take a few rydes to enjoy all your work and then it will be time to continue.....:gaah:
Good idea, but in Chicago we only have to seasons! Winter and summer! I don't enjoy riding when is cold! Besides, there still to much salt on the streets! Don't want to mess up my bike! Thanks!