Turn Signal

[Chief-J]

I have a 2011 RT-S. The turn signals (left or right) blinks very fast. All bulbs are good. When I use the four-way flashers, they blink slower (or normal). Could there be a problem with a ground wire?

Thank you.

[Bob Denman]

Have you added any extra turnsignal lights, or changed to LEDs?
If you haven't; then I would suspect a loose connection somewhere...

[finless]

Do you have any added lights hooked to the turn signals?
If not then double check all bulbs are working. You could have a couple out in the tail lights that might not look like it unless you inspect closely.
If you have any add-on lights you may need a resistor.

Bob

[Chupaca]

Give the search a whirl..there have been some postings on resetting the flasher speed. I think Lamont posted one of them...:thumbup:

[Cruzr Joe]

This should work to reset your turn signal speed

1. Turn key ON
2. PRESS & HOLD Hazard Button for 30 sec.
3. Cluster will flash once( I never saw this happen)
Reset Complete


Cruzr Joe

[billybovine]

This should work to reset your turn signal speed

1. Turn key ON
2. PRESS & HOLD Hazard Button for 30 sec.
3. Cluster will flash once( I never saw this happen)
Reset Complete


Cruzr Joe

Not on a 2011 only 2014 and newer.

[IdahoMtnSpyder]

I have a 2011 RT-S. The turn signals (left or right) blinks very fast. All bulbs are good. When I use the four-way flashers, they blink slower (or normal). Could there be a problem with a ground wire?

Thank you.
The hazard flasher is separate from turn signal operation and is made to flash proper speed regardless of too many or too few bulbs. You have too much or too little load on the T/S system. At worst the cluster has a problem.

[Flospyrida]

This should work to reset your turn signal speed

1. Turn key ON
2. PRESS & HOLD Hazard Button for 30 sec.
3. Cluster will flash once( I never saw this happen)
Reset Complete


Cruzr Joe

OMG Joe what would we do without you watching over all of us?
It works just like you said (But my Cluster did flash)
Thanks your the Wizard:bowdown::bowdown::clap::yes:

[Cruzr Joe]

OMG Joe what would we do without you watching over all of us?
It works just like you said (But my Cluster did flash)
Thanks your the Wizard:bowdown::bowdown::clap::yes:



:roflblack::roflblack:, Some times things work. ( I thought it worked on all models but maybe not)

Cruzr Joe

[SpyderAnn01]

Do you have a trailer harness? That, in combination with added LEDs, will cause the blinkers to blink fast.

[Flospyrida]

Yep added the BRP Hitch and Harness, hooked up the trailer lights to bike and signals would flash like strobes.
Trailer wiring is 5 wire + ground.

[MrSpacelySC]

I think the 2014 was the first year the turn signal flash speed was reprogrammable.

Where can I find appropriate "resistors" if I want to add spuderpops mirror turn signals?

Thanks
A Noob


This should work to reset your turn signal speed

1. Turn key ON
2. PRESS & HOLD Hazard Button for 30 sec.
3. Cluster will flash once( I never saw this happen)
Reset Complete


Cruzr Joe

[MrSpacelySC]

2011 RT... about to add spyderpops mirror turn signals and need directions once I experience the fast flashing--any sources out there?
Thanks
A Noob


Do you have any added lights hooked to the turn signals?
If not then double check all bulbs are working. You could have a couple out in the tail lights that might not look like it unless you inspect closely.
If you have any add-on lights you may need a resistor.

Bob