New Fuel Caps

[bruiser]

New fuel caps arrived today by post from BRP.

[Bob Denman]

Mailed directly to you, or did you hear this at the dealership?
Either way; :2thumbs:

[waytootall67]

I got the recall letter from BRP last week, they want me to bring the bike to the shop!!! Is the a Canadian thing?

[bruiser]

Came directly to my home. One for each RT.

[ARtraveler]

I will watch for the caps for both my 2010 and 2011.

[Bob Denman]

Oh, I just LOVE getting parts in the mail! :thumbup:
Time to start bugging the PostMistress! :lecturef_smilie:

[bruiser]

Is the a Canadian thing?

Must be a Canadian thing. Maybe they have to go through the dealership up there. I can't see why they would pay a dealer to do a one minute job.

[Bob Denman]

That is odd... :dontknow:
It's actually about a fifteen second job for most folks...
It does take me the full sixty! :opps:

[bruiser]

Put the new caps on. They do seem to have a tighter fit. A little more effort is needed to get them to "click". The new cap is larger and beefier. I'll post pics.

[Pennyrick]

I got the recall letter from BRP last week, they want me to bring the bike to the shop!!! Is the a Canadian thing?

Caps turn clockwise to close in the USA. In Canada they turn counter-clockwise.

[MarkLawson]

I got the recall letter from BRP last week, they want me to bring the bike to the shop!!! Is the a Canadian thing?

Was your recall, that requires a visit to the dealer, for the fuel cap or for the rerouting of the vent hose coming from the evaporator canister?

[ARtraveler]

It appears the recalls to bring the :spyder2: into the shop are for the vent hose fix.

[bruiser]

5969759698

Left picture shows new cap on the left, note larger size.
Right picture shows new cap on left. Again note larger size. Different vent baffle and larger gasket.

[bruiser]

Caps turn clockwise to close in the USA. In Canada they turn counter-clockwise.


No, that's Australia.

[jerpinoy]

Still waiting:coffee::coffee::coffee:

[SPYD3R]

DITTO on the gas cap...
59699

[JerryKaren]

Received mine in the mail today

[Freddy]

No, that's Australia.

Hey, I resemble that remark!

[bruiser]

Bob, I had to find a knife to open the boxes, then find the keys to the Spyders and walk down the steps to the garage. Insert key, raise seat, remove old cap, pick old cap up after dropping it, install new cap and close seat. That was on the wifes Spyder. Operation went smoother on my Spyder, I didn't drop the cap. :roflblack: I think the one minute for the dealer to do it is conservative. You'd probably have to leave it for three days for them to fit it in the schedule. :banghead:

[Plyrod38]

I received the new cap today also. My installation was easier as I already had the seat up with the battery tender on.
It will definately get the road test this weekend, sunny with temps in the mid 70"s.

[bruiser]

Hey, I resemble that remark!


:opps: Sorry Bro! :roflblack:

[Pandy]

I received the new cap today also. My installation was easier as I already had the seat up with the battery tender on.
It will definately get the road test this weekend, sunny with temps in the mid 70"s.

Yup, same here. Lot more effort to get it to click and a lot beefier. I now wonder if the hot weather gas smell will go away now. Warm here this weekend as well. I shall see.

Patrick

[Papa]

I haven't received mine yet but am wondering how easy it will be with the larger gas cap to get it on/off through the Ultimate seat fuel door. Anyone try yet?

[1551retired]

New fuel caps arrived today by post from BRP.

Did they send it via first class or priority mail? I've got standard mail forwarding while in FL for the winter. Hopefully the USPS with forward.

[Questions]

I may have missed some earlier posts but why are the caps being changed? To the best of my knowledge we have never been informed about any recalls for anything here in New Zealand. Maybe we get 'special' Spyders that are always perfect?

[thatk9guy]

Came home from work today and saw the package on the table, from the writing on the package label it reads "Important Safety Recall Notice", Shipped from Lachine QC, Canada to my residence in South Carolina. Will also take a ride with the warm weather this weekend and see if the Gas smell goes away.

[thatk9guy]

Attached are the front and back copy of the recall letter, I hope this helps.

[bruiser]

Did they send it via first class or priority mail? I've got standard mail forwarding while in FL for the winter. Hopefully the USPS with forward.

Standard post.

[bruiser]

I may have missed some earlier posts but why are the caps being changed? To the best of my knowledge we have never been informed about any recalls for anything here in New Zealand. Maybe we get 'special' Spyders that are always perfect?

They're sending notices and parts by packet ship to you folks down under :roflblack:

But seriously, you should be getting replacement caps as well.

[eddieshep999]

Hey, I resemble that remark!



In the UK We have a saying "IF THE CAP FITS WEAR IT"

[Laila's Dad]

...so since we all knew about the gas top issue, did anyone stop riding the spyder until the new gas top was sent or did you take your chances with the old one?

[SpyRyd]

...so since we all knew about the gas top issue, did anyone stop riding the spyder until the new gas top was sent or did you take your chances with the old one?

I haven't stopped ryding and I don't think anyone else has either...but I could be wrong...doubt it...but could be.

[thehawk]

I rode mine to work today with the old gas cap ... I'm just a risk-taking animal :roflblack:

thehawk

[DrewNJ]

I rode mine to work today with the old gas cap ... I'm just a risk-taking animal :roflblack:

thehawk

BOOM! :D

[SpyRyd]

BOOM! :D

Don't think so. Did you stop ryding waiting on your gas cap?

[Bob Denman]

http://smileys.smileycentral.com/cat/10/10_5_133.gifhttp://smileys.smileycentral.com/cat/10/10_5_133.gifhttp://smileys.smileycentral.com/cat/10/10_5_133.gif http://smileys.smileycentral.com/cat/4/4_1_72.gif

[NancysToy]

...so since we all knew about the gas top issue, did anyone stop riding the spyder until the new gas top was sent or did you take your chances with the old one?
If BRP felt you should stop riding, they would have told you so...and handled the recall differently. nojoke

[bruiser]

We didn't stop ryding either. I agree with Scotty. If you look at the number of Spyders on the road and the number that have experienced thermal events, you'll find it's a small %. And to my knowledge it's never been proven that the gas cap or vent hose were the cause. In fact the recall notice enclosed with the new cap states it's being replaced due to venting fuel vapors causing air pollution. Not for causing thermal events.

[AbNormy]

Still waiting on mine...:what::(

Sent from my SPH-D710 using Tapatalk 2

[Daisyjoe]

Got mine today. Installation was quick and simple.

[motoford]

Somehow I missed this whole fuel cap deal too... I searched for a thread on here and didn't see where this has been discussed before. Anyone got a link or have a 5 second summary of the issue and the years affected?

edit: nevermind it was right in front of me.

http://www.spyderlovers.com/forums/showthread.php?47591-Received-recall-today-from-BRP&highlight=fuel

[Laila's Dad]

Don't think so. Did you stop ryding waiting on your gas cap?

no, i probably took my longest ride on the spyder after the gas top issue was brought up. Plus my spyder is perfect, it's probably the only spyder on the list that had the right top already... Re-enactment: My wife "babe I smell gas". Me "must be one of those spyders with the faulty gas top". Wife "does yours have a bad gas top too?". Me "naah, we are good I think"... 10 minutes later. Wife "babe something is burning". Me ":shocked:". :roflblack:

[Yol Bolsun]

Received mine today.:thumbup:

[Bob Denman]

Sooooo... Has anybody figured out just what we should do with the OLD ones? :shocked:

[ARtraveler]

I will bet that a lot of people have an answer for that--but are going to keep it to themselves. :roflblack:

[SpyRyd]

Sooooo... Has anybody figured out just what we should do with the OLD ones? :shocked:

Recycle it!

[Bob Denman]

I will bet that a lot of people have an answer for that--but are going to keep it to themselves. :roflblack:

:shocked: :yikes: :gaah:

[boborgera]

Sooooo... Has anybody figured out just what we should do with the OLD ones? :shocked:

Ashtray, :shocked:

[cougar]

Anybody's gas mileage increase??

[bruiser]

Sooooo... Has anybody figured out just what we should do with the OLD ones? :shocked:


1.Turn 'em in to LED holders. Hey Reggie...:roflblack:
2.Skeet targets.
3.Send 'em to SpyderPops to recycle for bumpskids.
4.Take 'em to the dealer for refund. :shocked:
5.Trash 'em.
6. :dontknow:

[Macvid]

New fuel caps arrived today by post from BRP.

I got a new cap in mail.

[Ga Blue Knight]

Me too

[DrewNJ]

Don't think so. Did you stop ryding waiting on your gas cap?

Absolutely not....


Sent from my iPhone using Tapatalk

[Bob Denman]

1.Turn 'em in to LED holders. Hey Reggie...:roflblack:
2.Skeet targets.
3.Send 'em to SpyderPops to recycle for bumpskids.
4.Take 'em to the dealer for refund. :shocked:
5.Trash 'em.
6. :dontknow:

Refunds??? http://smileys.smileycentral.com/cat/4/4_1_72.gifhttp://smileys.smileycentral.com/cat/4/4_1_72.gifhttp://smileys.smileycentral.com/cat/4/4_1_72.gif :2thumbs:

Mounting LEDs on them? Hmmm...http://smileys.smileycentral.com/cat/4/4_12_12.gif

[MarkLawson]

Got them in the mail for both Spyders yesterday.

[Cavman]

Put on a chrome chain and wear as bling. :roflblack:

[MikeinGA]

Just got my new gas cap today for my 2011 RS-S. I looked up the price $28.99. A gas cap for my Jeep is 10.99 and gas cap for my Mustang is $12.99. Why is it 2 to 3 times more in price for a common part?


Mike

[Bob Denman]

Because they've had a lot more time to amortize the costs involved the Jeep and Mustang caps...

[BikerDoc]

Lots of Floridians including myself got them this week.

[WingmanRT]

Came directly to my home. One for each RT. Ditto.

[thehawk]

Because they've had a lot more time to amortize the costs involved the Jeep and Mustang caps...

i agree ... jeep and mustang have had lots more time to recover their R & D costs for their gas caps :roflblack::roflblack::roflblack:

thehawk

[bruiser]

Who cares. We didn't have to pay for them.

[effgjamis]

I have received my gas cap recall today... Funny, I was not aware it was on recall, what a surprise . However I periodically got a whiff of gas fumes, so I guess this new cap will correct that.


You don't suppose it will increase my gas mileage ?

[TicketBait]

got mine in the mail today:yes:

[Papa]

Still waiting :popcorn::popcorn::popcorn:

[Bob Denman]

:shocked: Me too! :shocked:
I feel like I've been left at the altar... :yikes:

[d.o.spyder-rts]

Still waiting in P. C. Fl Dale

[Cruzr Joe]

:shocked: Me too! :shocked:
I feel like I've been left at the altar... :yikes:

I am left at the altar with Bob, oh no.

Cruzr Joe

Sent by morse code from a hidden bunker

[boborgera]

Relax guys, Its only a gas cap, Not a pound of gold.
When it gets there' it gets there! Gee i've been waiting over a year for the radiator cap
for my Tri Glide.:rolleyes:

[Pandy]

Yup, same here. Lot more effort to get it to click and a lot beefier. I now wonder if the hot weather gas smell will go away now. Warm here this weekend as well. I shall see.

Patrick

Well, did 178 mile loop today, temps in the mid to upper 70s. Still have some gas smell when hot. Then again, it's done that from day one.
Nice gas cap though, I like new, free things.

Patrick

[Campverdefela]

Cha ching

[spyderpoop]

got mine cap today only had bike since end of Oct so this must be a new issue since then glad its a easy fix being safe is always good

[Highwayman2013]

Nothing here yet.

[stevedfive]

Mine arrived today.

[kyspydergal]

Nothing here yet either.

[Ivorspyder]

Received mine in the mail today.

Ivor:spyder:

[Bob Ledford]

Mailed directly to you, or did you hear this at the dealership?
Either way; :2thumbs:


My new cap came USPS In tOdays mail

[hackett43]

Mailed directly to you, or did you hear this at the dealership?
Either way; :2thumbs:





Even though my bike is in pieces, I got mine in the mail today.

[crazyspyder]

yup, walked in to my dealeship stated my case and walked out with one :chat:. AND then got re-embursed for the one I bought(still the old style) a couple of weeks ago after reminding them how long I have been complaining about my gas smell.:banghead:
cheers everyone!:2thumbs:

[Yeochief]

I got the letter about the vapor vent hose problem earlier this week. Just remembered to check the mail today, new gas cap was in the box. Put it on and canned the old one.
I have not had any gas smells with the old cap, :f_spider:is garaged and haven't noticed any fumes. My old cap must have been one of those that wasn't bad. New one is bigger and takes a tad more to get a click when closing.

I had my OEM seat redone by a professional who does motorcycle seats recently, added gel pad and we cut the corner of the pan and hinged it to allow me to refuel without lifting the seat. New larger cap fit without a problem. I am due for my 3600 mile oil change, will get the new larger filters when I visit the dealer for that. He recommended I go to 3000 miles before changing to the newer filters. no real need to change oil early just to get the new filter.

I am still evaluating the redo of the seat, and haven't decided what I will do with the BRP comfort seat the redo replaced. Will try to get pictures that show details of the fuel door and custom stiching to share. Tomorrow looks like a good day to take a ride.

[Spydee8]

I haven't received a letter or gas cap...:dontknow:

[Blue Star]

Re-enactment: My wife "babe I smell gas". Me "must be one of those spyders with the faulty gas top".

Thanks BRP, as you just took my excuse away while riding two-up :roflblack:

I got mine too. In fact, got two today. One for my old RS, and one for my RT. They both appear to be the same gas cap, and a bit heavier than the original.

[bruiser]

So, took a ride to the coast today. 250 miles round trip. Still had slight fuel smell but nowhere near as bad as before. It's probably from the vent line. Got home and parked them in the garage with 1/2 tank of fuel, no fuel smell. Before, had to leave them outside to cool down and disipate fuel vapors before putting them in the garage.

[oheresy]

Received my new gas cap in the mail yesterday. I didn't ride in to work tonight, so I haven't put it on yet.

[MrBones]

Are all of us getting new caps or just certain models?? I have a 2010 RSS.

[oheresy]

Are all of us getting new caps or just certain models?? I have a 2010 RSS.

Guess I should have mentioned that I have a 2011 RT-S.

[effgjamis]

As I have read through the post I get a hint about the installation of the new cap.
well here is simple solution I found.

1. Goto or stop at a Gas Station.
2. Remove old cap.
3. Refuel spyder
4. install new cap.
done.

:roflblack::roflblack::roflblack:

[Blue Star]

Are all of us getting new caps or just certain models?? I have a 2010 RSS.

I got one for each, but they appear to be the same cap.

[Chupaca]

Got ours in the mail today, larger seal (red! ) larger cap just as complicated a change as stated above.
As to why? there were gas fumes escaping and could accumulate under the seat. If any spark happened could ignite. :yikes:

[d.o.spyder-rts]

As I have read through the post I get a hint about the installation of the new cap.
well here is simple solution I found.

1. Goto or stop at a Gas Station.
2. Remove old cap.
3. Refuel spyder
4. install new cap.
done.

:roflblack::roflblack::roflblack:

Got mine in the mail today.

Or:

1. Go out to garage
2. Lift up seat
3. Remove old cap
4. Install new cap
5. Close Seat
6. Done
I didn't need any gas :roflblack::roflblack::roflblack: Dale

[spydeyblue]

We got the new gas cap and recall letter in the mail today. Unfortunately, I doubt the gas cap is the cause of the strong gasoline smell, which we got from our Spyder, both during and after our last ryde on our 2012 RT-S. After we got home, and the Spyder had been sitting for a few minutes, the husband did some investigating. He found liquid gasoline dripping from the outlet of a tube underneath the Spyder. After doing some research on this forum, we contacted the dealer, and took the Spyder in for repairs. Hopefully, they will be able to fix the problem! I am so grateful for this forum, where Paul and I can learn from fellow Spyder owners, instead of having to figure everything out myself!

Enjoy the Ryde!
Linda & Paul

[Bob Denman]

As I have read through the post I get a hint about the installation of the new cap.
well here is simple solution I found.

1. Goto or stop at a Gas Station.
2. Remove old cap.
3. Refuel spyder
4. install new cap.
done.

:roflblack::roflblack::roflblack:

You only forgot to mention step # 3a:
"leave old cap on top of the fuei pump."

[bhfromme]

Thank God mine came with instructions!

[Dar]

I haven't received a letter or gas cap...:dontknow:

Me Either:popcorn:

[Desert Spyder]

I got two gas caps today in the mail. I feel special since I didn't get my free tickets to the Long Beach international Bike show.

[ivanlee]

New fuel caps arrived today by post from BRP.

Got the new fuel cap with a value of $3.98 . if you have to purchased one from dealer it is about $29.00
what a mark up.:yikes:

[JJW SpyderRider]

Logged into the BRP site and it said my Spyder is effected by this recall but I have not seen anything yet. :dontknow: Never got the voucher for the oil change panel (Dealer still got me the panel).

[cougar]

I haven't received mine yet but am wondering how easy it will be with the larger gas cap to get it on/off through the Ultimate seat fuel door. Anyone try yet?




Fits just fine if you have an Ultimate Seat.

[Blue Star]

I got two gas caps today in the mail. I feel special since I didn't get my free tickets to the Long Beach international Bike show.

Proves BRP does have your mailing address.

[DrewNJ]

What's kinda funny is that there are people selling their recall caps on eBay. I figure either these are peeps that already replaced with the better atv cap or just refuse to believe the cap is the real issue....

On another note, I haven't received any info in the mail as of yet either.


Sent from my iPhone using Tapatalk

[Blue Star]

What's kinda funny is that there are people selling their recall caps on eBay. I figure either these are peeps that already replaced with the better atv cap or just refuse to believe the cap is the real issue....

On another note, I haven't received any info in the mail as of yet either.


Sent from my iPhone using Tapatalk

I saw that too. Could be people like me that received two gaz caps. I am going to keep my second gaz cap, as this way if I forget my gaz cap at the gaz station I won't have to buy another.

[jimclarkf1]

Is this for the RT only, or all SPYDERS? This is the 1st I have heard about it. THANKS

[Blue Star]

Is this for the RT only, or all SPYDERS? This is the 1st I have heard about it. THANKS

All Spyders.

[Dochands]

Nothing to my house yet.

[sinkhole]

Received mine today.

[BajaRon]

As I have read through the post I get a hint about the installation of the new cap.
well here is simple solution I found.

1. Goto or stop at a Gas Station.
2. Remove old cap.
3. Refuel spyder
4. install new cap.
done.

:roflblack::roflblack::roflblack:

You forgot to pay for your fuel! :lecturef_smilie:

[sonicsix]

I got my new gas cap in the mail today. When it stops raining 3 days from now, I will go put it on.

[3tracs]

:dontknow: Hope one comes, as I've recently had trouble removing the cap... it will sometimes just spin and not release. Was thinking I would have to buy a new one until I heard of this recall.

I'll be checking the mail box regularly... :pray:

[boborgera]

:dontknow: Hope one comes, as I've recently had trouble removing the cap... it will sometimes just spin and not release. Was thinking I would have to buy a new one until I heard of this recall.

I'll be checking the mail box regularly... :pray:


Happen to mine once at a gas station, I was about to brake it off with a screwdriver and hammer, Finely it came off. When i got home i put a light coat of white grease on the gasket, never had it happen again.

[BajaRon]

It's not a bad idea to put a little lubricant (the right kind) on your O-Ring once a year or so. I use a light, clear silicone/synthetic grease on mine. Keeps the O-Ring flexible, keeps it from drying out and cracking. And helps it to seal better and releases better too.

Be careful what you use though. I'd say some lubricants might attack the O-Ring compound.

[El Dorado Bob]

Arrived today via USPS. Was not expecting it, had me wondering for a moment when looking at the label, what is a gaz cap.:thumbup:

[pjweimer]

It's not a bad idea to put a little lubricant (the right kind) on your O-Ring once a year or so. I use a light, clear silicone/synthetic grease on mine. Keeps the O-Ring flexible, keeps it from drying out and cracking. And helps it to seal better and releases better too.

Be careful what you use though. I'd say some lubricants might attack the O-Ring compound.

Thought I read somewhere not to use silicone anywhere that may end up getting inhaled into a cylinder and burnt. Something about silicone will kill the catalytic converter in a heartbeat.:confused:

Sent from my GT-N8013 using Tapatalk 2

[Euripedes Neves]

Was your recall, that requires a visit to the dealer, for the fuel cap or for the rerouting of the vent hose coming from the evaporator canister?
I got my on the mail to and my spyder was at the dealer and they work on the vent hose e evaporator canister. I am very happy :yes::clap:

[boborgera]

Thought I read somewhere not to use silicone anywhere that may end up getting inhaled into a cylinder and burnt. Something about silicone will kill the catalytic converter in a heartbeat.:confused:

Sent from my GT-N8013 using Tapatalk 2


I was referring to a light coat on the gas cap gasket {o ring}

[bruiser]

Using silican sealers ie: RTV in an engine compartment can cause fumes from the RTV to be taken in through the air filter. It's not the CAT but the sensors that can be damaged. However, there are sensor safe silicans out now. But you must read the label. Ron is correct, a small amount of the correct lube is ok. Vasoline is my choice.

[eddieshep999]

It's not a bad idea to put a little lubricant (the right kind) on your O-Ring once a year or so. I use a light, clear silicone/synthetic grease on mine. Keeps the O-Ring flexible, keeps it from drying out and cracking. And helps it to seal better and releases better too.

Be careful what you use though. I'd say some lubricants might attack the O-Ring compound.

Ron or Others - I am still waiting for a replacement Fuel Cap from BRP Europe

When it comes I want to do what Ron suggested Ref - put a little lubricant (the right kind) on the O-Ring seal

I have 2 choices of Lubricants to use - Which should I use or can I use either ?

1 - Silicone Seal Ring Lubricant

2 - Vaseline(*) which is a brand of petroleum jelly (http://en.wikipedia.org/wiki/Petroleum_jelly) based products owned by Anglo-Dutch company Unilever (http://en.wikipedia.org/wiki/Unilever).

(*) Not sure if this is the same substance as described by Bruiser as Vasoline in his post

Thanks

[BajaRon]

Ron or Others - I am still waiting for a replacement Fuel Cap from BRP Europe

When it comes I want to do what Ron suggested Ref - put a little lubricant (the right kind) on the O-Ring seal

I have 2 choices of Lubricants to use - Which should I use or can I use either ?

1 - Silicone Seal Ring Lubricant

2 - Vaseline(*) which is a brand of petroleum jelly (http://en.wikipedia.org/wiki/Petroleum_jelly) based products owned by Anglo-Dutch company Unilever (http://en.wikipedia.org/wiki/Unilever).

(*) Not sure if this is the same substance as described by Bruiser as Vasoline in his post

Thanks

There isn't any way for prudent application of silicone to the gas cap O-Ring that is going to cause any issues with the engine. I don't recommend squeezing a glob of it into your fuel tank, now that might cause some interesting results.

I don't have a Cat on my Spyder so that issue is a non-starter for me.

Either of these suggested lubricants will work fine.

[Wazoo]

I received mine today, but found the instructions above about opening the box quite confusing. So instead I cut the box in half with a band saw to get it open. Unfortunately this also cut the new cap in half. I was concerned that using glue to put the two halves of the cap back together might do damage to the catalytic converter so I used heavy fishing line to sew it together and found some bamboo to put inside the threaded section to add strength. Unfortunately when I tried to screw the cap onto the bike the cap was a hair bigger than the opening. Sooo, I got some plaster of paris and made a mold of the new cap then converted my gas grill into a foundry which enabled me to melt some iron ore and cast an iron version of the repaired platic gas cap. I used a hand file to sharpen the threads on the iron cap then used the winch motor off my truck in combination with a vise grip to essentially use the iron cap as a giant drill bit to open up the opening on the gas tank. Now the repaired plastic cap fits on the bike but Im not sure I've solved the sloshing issue.

[wa3wheels]

I received mine today, but found the instructions above about opening the box quite confusing. So instead I cut the box in half with a band saw to get it open. Unfortunately this also cut the new cap in half. I was concerned that using glue to put the two halves of the cap back together might do damage to the catalytic converter so I used heavy fishing line to sew it together and found some bamboo to put inside the threaded section to add strength. Unfortunately when I tried to screw the cap onto the bike the cap was a hair bigger than the opening. Sooo, I got some plaster of paris and made a mold of the new cap then converted my gas grill into a foundry which enabled me to melt some iron ore and cast an iron version of the repaired platic gas cap. I used a hand file to sharpen the threads on the iron cap then used the winch motor off my truck in combination with a vise grip to essentially use the iron cap as a giant drill bit to open up the opening on the gas tank. Now the repaired plastic cap fits on the bike but Im not sure I've solved the sloshing issue.

I like the Vaseline better !! :yikes:

[boborgera]

In the old days if you lost/broke a gas cap, Real Men,
Would just stuff a rag in the opening and drive on. :dontknow:

[8 legs nz]

Hi you guys is this just a USA and Canada only replacement gas cap or is this would wide
:gaah:

[BajaRon]

Hi you guys is this just a USA and Canada only replacement gas cap or is this would wide
:gaah:

The issue is World Wide so I would think the FIX would also be world wide. Interesting....

[Silvervette05]

Got mine yesterday.

[EddieK]

My cap showed up in the mail yesterday now hopefully this will clear up the gas smell in the garage.

[Bob Denman]

In the old days if you lost/broke a gas cap, Real Men,
Would just stuff a rag in the opening and drive on. :dontknow:

I remember those! We called them "Molotov Cocktails"! :shocked:

[Bob Denman]

I received mine today, but found the instructions above about opening the box quite confusing. So instead I cut the box in half with a band saw to get it open. Unfortunately this also cut the new cap in half. I was concerned that using glue to put the two halves of the cap back together might do damage to the catalytic converter so I used heavy fishing line to sew it together and found some bamboo to put inside the threaded section to add strength. Unfortunately when I tried to screw the cap onto the bike the cap was a hair bigger than the opening. Sooo, I got some plaster of paris and made a mold of the new cap then converted my gas grill into a foundry which enabled me to melt some iron ore and cast an iron version of the repaired platic gas cap. I used a hand file to sharpen the threads on the iron cap then used the winch motor off my truck in combination with a vise grip to essentially use the iron cap as a giant drill bit to open up the opening on the gas tank. Now the repaired plastic cap fits on the bike but Im not sure I've solved the sloshing issue.

:shocked: Dude... :roflblack: :thumbup:

[Grandpa Pete]

Hey guy's, is this "fix" only for earlier models. I've got a 2012 RTS SE5 and have not recieved a notice, post card, carrier pidgeon, nada for anything on my bike. Just curious..thx

[Lamonster]

Hey guy's, is this "fix" only for earlier models. I've got a 2012 RTS SE5 and have not recieved a notice, post card, carrier pidgeon, nada for anything on my bike. Just curious..thx

It's for all Spyders.
http://spyder.brp.com/blog/post-details?PostID=ea6cc7c9-764b-44ad-9647-a12e00f66679

[Bob Denman]

Patience... it'll come! :thumbup:

[oldgoat]

Any Canadians received a replacement gas cap yet?

I haven't.

[groundeffect]

Any Canadians received a replacement gas cap yet?

I haven't.

Yes, I did. Note that I think BRP have focused first on contacting customers in warmer climates at this time of year.

[groundeffect]

Hey guys!!!


Got my new spyder gas tank cap in the mail the other day, direct replacement. Out with the old, in with the new.


Cheers from Newfoundland.

[Rando]

Anyone need a new gas cap? Pay the shipping and it's yours. I ended up with two.

[Rotaxer]

Just received mine this week in Alberta. Now where is that install video????????