Any experience using these Dolly Jack's for moving Spyder?

[USAF]

Has anyone used one of these dolly jacks on your rear wheel to move your spyder around the garage out of the way ? And will it work with a 2022 Spyder RT ?

[EdMat]

It will but it is very tight if you try to put it fully under the tire before you start to lift. Works great on the front.

[BLUEKNIGHT911]

It will but it is very tight if you try to put it fully under the tire before you start to lift. Works great on the front.

:agree: .... I think the Lifting lever is not going to be accessible for the rear wheel .... I bought small wood framed moving doolies from either Harbor Freight or Home Depot .... 12 X 14-16 .... the rear wheel fit inside very nice .... I know you have to jack up the Spyder to do this, but I seldom needed to do this ....Mike :thumbup:

[Jesster72]

:agree: .... I think the Lifting lever is not going to be accessible for the rear wheel .... I bought small wood framed moving doolies from either Harbor Freight or Home Depot .... 12 X 14-16 .... the rear wheel fit inside very nice .... I know you have to jack up the Spyder to do this, but I seldom needed to do this ....Mike :thumbup:

I got the Harbor Freight car dollies. I would have preferred the softer nylon rollers, but I use them twice a year - once to roll the Spyder to the back of the garage, and then to move it out to wake it up. I think I spent about $100 for the set of 4, and I already had a floor jack to get the bike up in the air, so it worked out for me.

[2dogs]

Exactly as BK911 said. It's the least expensive, quickest, and safest way to move around and store your spyder for the season.

[USAF]

I was also thinking of getting these without the jack like already mentioned. I think this is the route I may go with.

[USAF]

:agree: .... I think the Lifting lever is not going to be accessible for the rear wheel .... I bought small wood framed moving doolies from either Harbor Freight or Home Depot .... 12 X 14-16 .... the rear wheel fit inside very nice .... I know you have to jack up the Spyder to do this, but I seldom needed to do this ....Mike :thumbup:

You are saying a wood framed dolly will hold the weight of the spyder ? Do you have a picture of what you purchased ? That would be a much cheaper way to go.

[YIRYDE]

I got the Harbor Freight car dollies. I would have preferred the softer nylon rollers, but I use them twice a year - once to roll the Spyder to the back of the garage, and then to move it out to wake it up. I think I spent about $100 for the set of 4, and I already had a floor jack to get the bike up in the air, so it worked out for me.

I brought the same thing to move two Spyders around in the garage, works great for storing during the winter. Can move the Spyders around without the need to start them.

[YIRYDE]

I was also thinking of getting these without the jack like already mentioned. I think this is the route I may go with.

They work great, lift up the Spyder a couple of inches off the ground and slide them under wheels.

[BLUEKNIGHT911]

You are saying a wood framed dolly will hold the weight of the spyder ? Do you have a picture of what you purchased ? That would be a much cheaper way to go.

No pic - Sometimes I use all three, and sometimes just one under the rear wheel. .... ZERO issues with weight. ... Bought them over 14 years ago. ..... Mike :thumbup: .... Just looked on Harbor Freight. ... hardwood 1000 lb rated 12" X 18" - $ 12.95 ea.

[2dogs]

I have one of those little HF wooden dollies under a small antique business safe made of steel and concrete that weighs close to 500 lbs. and it's as good and sturdy as the day I bought it. That's close to half of an RT.

[Mikey]

I was also thinking of getting these without the jack like already mentioned. I think this is the route I may go with.

I have used my sled dolly's that look a lot like these, work great!!!

[BigPoppa]

I was also thinking of getting these without the jack like already mentioned. I think this is the route I may go with.

I bought similar ones off Amazon to complement my Big Blue lift. I haven’t used them yet though, they’re still in the box.

[Bensonoid]

They're on sale now at HF.

[blacklightning]

They're on sale now at HF.
I also use those to attach my shop working stool to. The wheels on the stool always break off. So I just take them off and bolt the entire thing to the wooden dolly. Works great, and raises it up about an inch.